Manual NAD c425 (page 8 of 68) (English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish)

161044

Zoom out

Zoom in

1/68

ENGLISH FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

STORING, RECALLING AND LABELLING PRESETS

Up to 30 presets in total can be stored in the C 425’s memory bank;

these can be any mix of either AM or FM stations. When scrolling

through the presets, empty preset places will be skipped; it is thus

possible to go from preset No. 4 to No. 7 without having seen No. 5 and

6. With the presets you can also store whether you want Blend (No. 3)

and FM Mute/Mode (No. 5) to be activated as well every time you recall

the preset.

To Store a Preset

• Tune to the radio station you wish to enter into a Preset (refer to

this chapter’s section 10). If the station is transmitting RDS

information, the RDS indicator will light up and station initials or

name will be shown in the Display Panel. If a non-RDS station is

found, then just the frequency will be shown.

• Select Blend (No. 3) or FM Mute/Mode (No. 5) if desired.

• To store that station as a Preset, press Memory (No. 4). The Preset

number and the red "MEMORY" indicator are flashing in the

Display Panel. The lowest available empty preset number will be

shown. If no other buttons are pressed within 12 seconds, the

tuner will revert to its previous state.

• Press Memory again to store the preset. If you wish to assign a

different preset number, rotate the PRESET/TUNE control left or

right to select the desired preset number. You can overwrite an

existing preset. If the preset number already has been assigned,

"MEMORY" will stop blinking, but the preset will continue to

blink. When you have selected the desired preset number, press

Memory again to store the station.

NOTE

You can enter a new station into an unused Preset or over-write an

existing programmed Memory Preset. By doing this you will replace

all the data previously held on that Preset number. When Memory is

pressed during normal operation, the Preset number and the red

"MEMORY" indicator will flash in the Display Panel. If no other

buttons are pressed within 12 seconds, the tuner will revert to its

previous state. The Memory Presets have a memory back-up, so they

will remain stored for several weeks even if the Tuner is switched off

or unplugged from the mains supply.

RECALLING A PRESET

• To select a Preset station, the C 425 must be in the Preset mode

(the display indicates "PRESET"). If not, press the PRESET/TUNE

Mode button (No. 8); "PRESET" will now light up in the display.

• Rotate the Tune/Preset control (No. 10) in either direction until the

right Preset is found and shown in the Display Panel. Any unused

Presets will be skipped; this avoids having to scroll through empty

presets.

DELETING A STORED PRESET

You can empty a Preset by deleting the stored information:

• Select the Preset to be emptied.

• Press and hold the Memory button (No. 4) and Display button

(No.7) for two seconds. The preset number and the text

"DELETE" will flash in the display.

• Press only the display button again (within default time of 5

seconds) to confirm you want to delete this preset. The text

"DELETED" and "—" as the Preset number appear in the display

for a couple of seconds.

LABELLING A PRESET

When a station is transmitting RDS information, your NAD C 425 will

automatically show the station initials when its Preset is used. Although

the Tuner automatically shows the frequency of any other AM or non-

RDS Preset station, it also allows you to type in the station name to make

it easier to identify which station is stored in the Memory Preset.

To enter a name:

1 Select the Preset you want to attach a name to.

2 Press and hold the Display button (No. 7) for two seconds. The first

space in the Station Data area of the Display Panel will flash.

3 Rotate the PRESET/TUNE Control (No. 10) in either direction to scroll

and select the first character (see Character list below for reference).

4 Press Display to move one place to the right to enter the next desired

character.

5 Rotate the PRESET/TUNE Control again to select the next character in

the name and press Memory to store it.

6 Repeat steps 3 to 5 until name is complete or all eight places have

been filled (up to 8 characters).

7 Press Memory once to finish the labelling procedure. Press Memory

again to store the completed name.

There are 37 characters available including a blank space.

NOTE

This function is available only for non-RDS stations. RDS Stations will

always display their transmitted name and cannot be over-written.

SPACE

A B C D E F G H I

J K L M N O P Q R S

T U V W X Y Z 0 1 2

3 4 5 6 7 8 9

Operation

C425 072006.qxd 7/28/2006 11:31 AM Page 8

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NAD c425 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NAD c425 Manual

Product: