581050
9
Zoom out
Zoom in
Previous page
1/12
Next page
The C 427 oers very high quality sound from radio broadcasts. The
reception and sound quality will always be dependent to a degree however
on the type of antenna(s) used as well as proximity to the broadcast origin,
geography and weather conditions.
ABOUT ANTENNAS
The supplied ribbon-wire FM antenna can be connected to the rear panel
FM-antenna input using the included “balun” adapter and should be fully
extended to form a T. This folded-dipole antenna will usually work best
when oriented vertically, with the arms of its T fully outstretched and
arranged perpendicular to the origin of the desired broadcast. There are
no “rules however, and experimenting freely with antenna placement and
orientation may yield the clearest sound and lowest background noise.
In areas of poor FM reception, an exterior FM antenna can improve
performance dramatically. If radio listening is important to you, consider
consulting an antenna installation professional to optimize your system.
The supplied AM loop antenna will usually provide adequate reception.
However, an exterior AM antenna can be used to improve reception.
Consult an antenna professional for more information.
ASSEMBLING THE LOOP ANTENNA
1 Rotate the outer frame of the antenna.
2 Insert the bottom edge of the outer frame into the groove on the stand.
3 Extend the antenna cord.
SELECTING A TUNER BAND
Select AM or FM band by pressing corresponding front panel button. Using
the TNR 3, select desired band by directly pressing [AM] or [FM] button.
TUNING STATIONS
Toggle front panel’s [PRESET/TUNE/SCROLL] control knob to switch
between “Presets and Tune” mode. Select Tune or “Presets . Tune” or
“Presets” will be displayed in the second line of the VFD depending upon
the mode selected.
DIRECT TUNING
If you know your desired station’s frequency allocation, you can tune
directly to the station.
1 Toggle front panel’s [PRESET/TUNE/SCROLL] control knob to switch
between “Presets and Tune” mode. Select TUNE mode.
2 Using the numeric keys of the remote control, key-in the frequency
allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,
“4”, “5” and “0” or press “1”, “0”, “4” and “5”.
STORING PRESETS
The C 427 can store a mix of your 40 favorite AM and FM stations for
immediate recall.
1 To store a desired AM/FM station to a preset, rst tune to the desired
frequency, then press the front panel’s [MEMORY] button. The VFD will
show the next available Preset number - for example, “Preset 04 Free”.
2 Press [MEMORY] button again to store the desired frequency on the Preset
number shown (“P04” is shown in the upper right corner of the VFD). Your
desired frequency is now stored in the assigned preset number.
DIRECT RECALL OF A PRESET
You can directly recall a desired Preset number.
1 Toggle front panel’s [PRESET/TUNE/SCROLL] control knob to switch
between “Presets and Tune” mode. Select “Presets mode.
2 Using the numeric keys of the remote control, key-in directly your
desired Preset number.
DELETE A PRESET
Selected Preset (for example, “P04”) can be deleted using either of the
following methods.
Using front panel buttons
Press and hold front panel button’s [BLEND] and then [MEMORY] to
delete selected Preset – “P04” transforms to “P--“.
Using TNR 3
Press and hold TNR 3’s [DEL] button until “P04” transforms to “P--“.
ABOUT RDS
The Radio Data System (RDS) permits sending small amounts of digital
information using conventional FM radio broadcasts. The C 427 supports
two RDS modes, program-service name (PS mode) and radio-text (RT
mode). Not every FM station incorporates RDS in its broadcast signal. In
most areas you will nd from one to several RDS-enabled stations, but it is
by no means impossible that your favorite stations will not be broadcasting
RDS data.
When an RDS-enabled FM broadcast is tuned, the VFD will show its
program-service name (PS) text and the station’s radio-text (RT) readout,
if any, which might scroll song- or artist-name, or any other text of the
stations choosing.
OPERATION
LISTENING TO AM/FM RADIO
9
ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
9


Need help? Post your question in this forum.

Forumrules
1

Forum

nad-c-427

Reset search

  • comment changer le pas de recherche en AM de 9k en 10k sur NAD C427 Submitted on 11-4-2017 at 08:48

    Reply Report abuse
  • comment commuter le pas de recherche en AM de 9k en 10k Submitted on 11-4-2017 at 08:38

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C-427 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C-427 in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C-427

NAD C-427 Quick start guide - English - 2 pages

NAD C-427 User Manual - German - 12 pages

NAD C-427 User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info