610990
3
Zoom out
Zoom in
Previous page
1/25
Next page
03
iVECTOR Heater/Cooler
1.0 Introduction
2.0 Warnings & Safety Measures
This heater/cooler fan convector is designed for use on
central heating systems or heating and cooling systems in
homes and commercial environments. Models are available
with 2 and 4-pipe connections.
The control system provides thermostatic room temperature and
automatic fan speed control, and allows operation on a
stand-alone basis, or by integration into building management
systems.
The unit is fitted with a washable air filter that can be easily
removed for cleaning (see Section 14).
A range of accessories are available for this product including
control valves and condensate pumps for cooling installations
(see Section 15).
l Please carefully follow the instructions and guidelines
contained in this manual during installation. Always perform
each step in sequence.
l Inspect this product for concealed shipping damage prior to
installation. If items are damaged or missing please contact
your supplier.
l This fan convector must be installed by qualified engineers.
l This fan convector must not be installed immediately below a
socket outlet.
l Do not install this fan convector in areas where excessive
dust exists.
l This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience or knowledge, unless they
have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
l The manufacturer accepts no liability for damage or injury
caused by failure to adhere strictly to the safety precautions
and instructions contained in this manual, or by negligence
during the installation of the product and any accessories
described in this manual.
l For the correct installation of this unit it is essential that
fixing is carried out in such a way that it is suitable for
intended use and predictable misuse. A number of elements
need to be taken into consideration including the fixing
method used to secure it to the wall, the type and condition
of the wall itself, and any additional potential forces or
weights that may happen to be applied to the unit, prior to
finalising installation.
l Please leave this manual with the end user.
3.0 Heating System Design
1.02.0
3.0
This manual should be read carefully prior to installation and retained by the customer for future reference.
This heater/cooler should only be used on closed circulation, two pipe, pump assisited central heating
systems or heating and cooling systems.
This unit MUST NOT be installed in a bathroom or other high humidity area.
This appliance must be earthed.
DO NOT cover or obstruct the air inlet or outlet grille.
Disconnect the unit from the power supply before carrying out any maintenance work.
This heater/cooler fan convector is designed for wall mounted
installation.
For optimum fan convector performance the system must be
capable of providing sufficient flow of water through the heat
exchanger at the correct temperature. This means that:
1. The unit is not suitable for use on microbore pipework.
2. This unit is not suitable for 1 pipe systems.
3. Optimum performance will require effective balancing of the
whole system. Each emitter on the circuit should be checked
and valves adjusted so that the required water flow rate
through each unit is achieved (see Section 15 for valves).
4. Where the unit is fitted on to a system with other emitters a
separate circuit for the fan convector should be considered
in order to provide sufficient flow through the unit.
5. The system water must be above 32°C for heating mode and
below 15°C in cooling mode.
6. This unit must not be used to replace a radiator in an existing
heating system unless an adequate flow of water through the
unit can be guaranteed (see Section 11 for flow rates).
iVECTOR HEATER/COOLER
INSTALLATION, OPERATING, MAINTENANCE & AFTER SALES MANUAL
SS
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Myson iV140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Myson iV140 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Myson iV140

Myson iV140 Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info