490358
4
Zoom out
Zoom in
Previous page
1/48
Next page
www.mtxaudio.com - www.mtxaudio.eu
Owners Manual - RT1000.1D
Installation & Mounting
MTX recommends your new RoadTHUNDER amplier be installed by an Authorized MTX retailer. Any devia-
tion from specied installation instructions can cause serious damage to the amplier, speakers and/or vehicles
electrical system. Damage caused from improper installation is NOT covered under warranty. Please verify all
connections prior to system turn on !
1. Disconnect the vehicle’s negative battery cable.
2. Determine the mounting place for your MTX amplier. Keep in mind there should be sucient air ow for
proper cooling. Mark the mounting holes from the amplier to be drilled. Before drilling make sure all vehicle
wires, gas lines, brake lines and gas tank are clear and will not interfere with installation. Drill the desired holes
and mount the MTX amplifier.
3. Install a positive (+) power cable from the vehicles battery through the rewall using a grommet or rewall
bushing to avoid cable damage from sharp edges of the rewall. Run the cable through the interior of the vehicle
and connect it to the amplier’s (+12V) terminal. Do Not connect to the battery at this time.
Note : Use only proper gauge wire for both positive and negative connections.
4. Install a circuit breaker or fuse within 20cm of the battery. This eectively lowers the risk of severe damage to
you or your vehicle in case of a short circuit or accident. Make sure the circuitbreaker is switched o or the fuse
is taken out of the fuse holder untill all connections are made. Now connect your positive power cable to the
positive battery terminal of the battery.
5. Grounding - Locate a proper ground point on the vehicle’s chassis and remove all paint, dirt or debris to reveal
a bare metal surface. Attach the ground wire to that contact point. Connect the opposite end of the ground wire
to the (GND) terminal on the MTX amplier.
6. Connect a Remote Turn-on wire from the source unit to the MTX amplier’s (REM) terminal. If the source unit
does not have a dedicated Remote Turn-on lead, you may connect to the source unit’s Power Antenna lead.
7. Connecting signal cables to the amplier : There are two ways to supply the signal to your MTX amp.
To get maximum performance, we suggest connecting a high quality RCA to the corresponding outputs at the
source unit and inputs of the amplifier.
If a source unit is being used without RCA outputs, use the included high-level ampliers speaker terminals
using the right gauge speaker wire.
8. Connect your speakers to your MTX amplier’s speaker terminals using the right gauge speaker wire. Your MTX
amp can drive a 2Ω minimum load for max power.
9. Double check all previous installation steps, in particular, wiring and component connections. Once veried,
reconnect the vehicles negative battery cable, turn the circuit breaker on or place the fuse in the fuse holder.
Note : Gain Levels on the amplier should be turned all the way down (counter clockwise) before proceeding
with adjustments.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTXaudio RT1000-1D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTXaudio RT1000-1D in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info