Manual Mtx audio x1000d (page 3 of 36) (English, German, Dutch, French, Italian, Portuguese, Spanish)

167884

Zoom out

Zoom in

1/36

www.mtx.com - www.mtxaudio.eu

4. Input selection switch - This switch, is used to match the ampliﬁer’s input to the source unit’s or DSP unit’s output.

If your source unit or DSP unit has a mono output you can select: Mono L or Mono R as your input connection,

if your source unit or DSP unit has a stereo output you need to select SUM for input now both RCA inputs of the

ampliﬁer are active and the stereo signal will be converted into a mono signal by the ampliﬁer.

5. EBC port - For connecting the included External Bass Control. A remote bass control so the bass can be adjusted

from the driver’s seat.

6. Subsonic ﬁlter control - This control is used to select the desired (high pass) subsonic ﬁlter frequency. The sub-

sonic ﬁlter protects the subwoofer(s) against too low frequencies that can dammage the subwoofer(s).

7. Low pass x-over frequency control - This control is used to select the desired low pass x-over frequency. The

frequency can be adjusted between 40Hz and 200Hz.

8. Speaker Terminals – Be sure to observe speaker polarity through the system. Failing to wire the speakers in

proper phase could result in a loss of bass response and/or poor

overall sound quality.

Caution : The X1000D ampliﬁer is not recommended for loads below 2 ohms.

9. Fuse - For convenience, all MTX XTHUNDER ampliﬁers utilize ATC type fuses. For continued protection in the

event that a fuse blows, replace the fuse only with the same value.

Caution : The power fuse on the amp is for protecting the amp against overdrive. To protect the vehicle’s electrical

system, an additional fuse is required within 30cm of the battery on the 12V+ cable.

10. Power Terminal – This is the main power input for the ampliﬁer and must be connected directly to the positive

terminal of the car battery for the ampliﬁer to operate properly. Use caution when running this cable through the

vehicule. Try to avoid running this cable along side the input RCA cables, antenna cabling, or other sensitive equi-

pment as the large amount of current ﬂowing through this cable can induce noise into your system. It is also very

important to have a tight connection to ensure maximum performance. We recommend to use 10mm2 or larger

power wire with the MTX XTHUNDER X1000D ampliﬁer.

11. Remote Terminal – The Ampliﬁer can be turned on by applying 12 volts to this terminal. Typically this voltage is

supplied by a wire from the source unit marked “remote” or “electric antenna”.

12. Ground Terminal – A good quality ground is required for your Ampliﬁer to operate at peak performance. A short

length of cable the same gauge as your power cable should be used to attach the ground terminal directly to the

chassis of the vehicle. Always scrape or sand any painted surfaces to expose bare metal where the ground wire

will attach.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mtx audio x1000d in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mtx audio x1000d Manual

Product: