629100
16
Zoom out
Zoom in
Previous page
1/18
Next page
Operating Manual English
13
Note
Follow the instructions in the
operating manual for your battery
charger.
Replacing fuses
Replace defective fuses only with
ones of an equal strength.
Once per season
Lubricate all rotating and bearing
points (operating lever, height
adjustment of the cutter deck ...)
with several drops of light oil.
Clean the spark plug and check
the gap between the electrodes
or replace the plug. See engine
handbook.
The rear axles must be lubricated
with a special-purpose (water-
repellent) grease at a specialised
garage.
Have the cutting blade
sharpened or replaced in
a specialist workshop.
Note
Regularly check (when visiting your
workshop) the condition of the
mower deck V-belt.
Removing/Installing and
adjusting cutter deck
Danger
Injury hazard if engine is started
inadvertently
Protect yourself against injury.
Before carrying out any work on the
mower
park the appliance on a level
surface,
switch off the engine,
withdraw the ignition key,
switch off PTO,
lock the parking brake.
wait until all moving parts have
come to rest and the engine has
fully cooled,
remove the spark plug connector
on the engine in order to prevent
the engine from accidentally
being started.
Danger
Injury hazard due to sharp cutting
blade.
Wear protective gloves.
Disassembly
Raise cutter deck into a position
in which the V-belt is as
horizontal as possible between
the cutter deck and PTO clutch.
Remove the V belt (1) from the
PTO clutch/motor pulley (2) –
fig. 20.
To do this, pull left or right side of
the V-belt backwards and then
downwards while manually
turning the engine belt pulley in
the opposite direction.
Note:
Work carefully to avoid
trapping your fingers.
Move cutting height adjustment
lever to the lowest position.
Remove front fixing bracket from
the cutter deck – Fig. 19. Pull
cotter pin (1) and pull the fixing
bracket (2) out of the holder.
Note:
In doing so, support the
cutters firmly so that they cannot
simply drop to the ground.
Pull out the pin (1) on the left and
right of the cutter deck to
disconnect the cutter deck from
the hanger (2) – Fig. 13.
Note:
In doing so, support the
cutters firmly so that they cannot
simply drop to the ground.
Move cutting height adjustment
lever to the highest position.
Pull out the cutters from beneath
the appliance.
Assembly
To reinstall the cutters perform the
above steps (for removing the
cutters) in reverse order. Work
proceeds faster when you are
assisted by a second person. Make
sure that the suspension units are
in their respective recesses on the
cutter mount and the pin has
engaged correctly.
Note
Following assembly, check that the
V-belt is positioned correctly and is
not twisted – Figs. 21 to 23.
Setting the cutter level
When mowing does not appear to
be parallel to the lawn the cutters
can be aligned.
Note
Before aligning the cutters check
the tyre pressure on the appliance.
Setting the side level
Fig. 11
Raise the cutters to the top.
Carefully turn the outer cutters
(risk of injury) transverse to the
drive direction.
Measure the distance between
the ground and the ends of the
two outer cutters. The result
should be the same. If required,
set the correct level by rotating
the setting segment (2) on the left
cutter deck side. To do so first
loosen (but do not remove) the
cap bolt (1) and retighten this
after the adjustment.
Set the level from front to back.
Fig. 10
Note
Set/check the side level before this
adjustment.
Raise the cutters to the top.
Carefully turn the outer cutters
(risk of injury) parallel to the drive
direction.
Measure the distance between
the ground and the end of the
right cutter. The end of the front
cutter should be about 3.2–6 mm
lower than the end of the rear
cutter. You may have to adjust
the front receiver (1). To do this,
set the correct level by adjusting
the nut (2).
Voltmeter Battery
charging
state
Charging
time
12.7 volts 100 %
12.4 volts 75 % approx.
90 min.
12.2 volts 50 % approx.
180 min.
12.0 volts 25 % approx.
280 min.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD Zero Turn Serie RZT-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD Zero Turn Serie RZT-S in the language / languages: English as an attachment in your email.

The manual is 6,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD Zero Turn Serie RZT-S

MTD Zero Turn Serie RZT-S User Manual - German - 18 pages

MTD Zero Turn Serie RZT-S User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info