507836
16
Zoom out
Zoom in
Previous page
1/18
Next page
Operating instructions for lawn tractors English
13
The rear axles must be lubricated
with a special-purpose (water-
repellent) grease at a specialised
garage.
Have the cutting blade sharpened
or replaced in a specialist
workshop.
Note
Regularly check (when visiting
your workshop) the condition
of the mower deck V-belt.
Installing/removing and
adjusting cutter deck
a~åÖÉê
oáëâÑåàìêóêçãåÖáåÉí~êíáåÖ=
ìåáåíÉåíáçå~ääó
mêçíÉÅí=óçìêëÉäÑ=Ñêçã=áåàìêóK=_ÉÑçêÉ=
ÇçáåÖ=~åó=ïçêâ=íç=íÜáë=~é éäá~åÅÉ W
Ó é~êâ=íÜÉ=~ééäá~åÅÉ=çå=~=äÉîÉä=
ëìêÑ~ÅÉI
Ó íìêå=íÜÉ=ÉåÖáåÉ=çÑÑI
Ó êÉãçîÉ=íÜÉ=áÖåáíáçå=âÉóI
Ó ëïáíÅÜ=çÑÑ=mqlI
Ó äçÅâ=íÜÉ=é~êâáåÖ=Äê~âÉI
Ó ï~áí=ìåíáä=~ää=ãçîáåÖ=é~êíë=Ü~îÉ=
ÅçãÉ=íç=êÉëí=~åÇ=íÜÉ=ÉåÖáåÉ=Ü~ë=
Ñìääó=ÅççäÉÇI
Ó êÉãçîÉ=íÜÉ=ëé~êâ=éäìÖ=ÅçååÉÅíçê=
çå=íÜÉ=ÉåÖáåÉ=áå=çêÇÉê=íç=éêÉîÉåí=
íÜÉ=ÉåÖáåÉ=Ñêçã=~ÅÅáÇÉåí~ääó=ÄÉáåÖ=
ëí~êíÉÇK
a~åÖÉê
oáëâ=çÑ=áåàìêó=Ñêçã=ëÜ~êé=ÅìííÉêëK
tÉ~ê=éêçíÉÅíáîÉ=ÖäçîÉ ëK
Assembly
Note
Work proceeds faster when you
are assisted by a second person.
Mounting the cutting
mechanism
Move the cutting height setting
lever into the top catch (HI/16).
or
For units with electric cutter deck
lifter: Move lever for setting the
height/depth to the lowest position
(LO/1) and press the switch
for the electric lifter backwards.
Push cutter deck from the right side
under the tractor.
Fig. 19
Align cutter deck so that the rear
cutter deck holders (1) are under
the locating holes (2) of the lifting
arms (3).
Lower lifting arms (3):
Move cutting height adjustment
lever to the lowest notch (LO/1).
or
For units with electric cutter
deck lifter: Press switch for
the electric lifter forwards.
Fig. 20
Pull out the J-handle (1) on the left
cutter deck holder (2). Lift the back
of the cutter deck slightly until you
can press the J-handle into the
locating hole of the lifting arm (3).
Ensure that it engages correctly.
Repeat this work step on the right
side of the cutter deck.
Fig. 21
Remove the two nuts from the
fixing bracket (1).
Attach fixing bracket (1) to the
holders (2) on the cutter deck.
Insert the ends of the fixing bracket
into the locating holes of the holder
(3) on the tractor.
Screw the two nuts back onto
the fixing bracket.
Note: Do not tighten the nuts yet.
Attaching the drive belt
Note
The “V” side of the drive belt must
be in the belt pulleys.
Fig. 22
Place drive belt (1) on the engine
coupling belt pulley (2) (PTO).
Feed drive belt downwards and
place on the two deflection belt
pulleys (3).
Note: On the right deflection belt
pulley the V-belt guide (4) must
be bent outwards slightly so that
the drive belt can be attached.
After attaching the drive belt, bend
V-belt guide back!
Feed drive belt backwards and
attach it to the cutter deck.
Fig. 23
Press belt pulley holder (1) on
the cutter deck backwards,
the belt pulley moves forwards.
Place the drive belt on the belt
pulley (1, Fig. 24). Slowly feed the
belt pulley holder back.
=oáëâ=çÑ=áåàìêóK
qÜÉ=ÄÉ äí= é ìääÉó=ÜçäÇÉê= áë=ìåÇÉê= ëíêçåÖ=
ëéêáåÖ=íÉåëáçå=Ó=ïçêâ=ïáíÜ=ÉñíêÉãÉ =
Å~ìíáçå>
Check that the drive belt is positio-
ned correctly on all belt pulleys.
Installing the spacer (stop
for the cutter deck lifter)
Fig. 25
Note
The spacer must be installed before
the cutter deck is set.
Using the screws (2), attach
the two holders (1) to the right and
left sides of the tractor frame.
Note
If the cutter deck has a cutting width of
107 cm, only one
spacer is attached
to the left
side of the tractor frame.
Removing the transport secu-
ring device at the ejector flap
Fig. 18
Depending on the model remove
the locking plate or cable tie.
The deflector closes automatically.
Setting the cutter level
t~êåáåÖ
^ÑíÉê=áåëí~ääáåÖ=íÜÉ=ÅìííÉê=ÇÉÅâI=
ëÉí=íÜÉ=ÅìííÉê=ÇÉÅâ=äÉîÉäK
Note
Before aligning the cutters check
the tyre pressure on the appliance.
Set the level from front to back.
Fig. 26
Move the cutter deck to a medium
height position.
Carefully turn the outer cutters
(risk of injury) parallel to the drive
direction.
Measure the distance between
the ground and the end of the right
cutter. The end of the front cutter
should be about 6–10 mm lower
than the end of the rear cutter.
You may have to adjust the front
receiver (1). Set the correct level
by adjusting the nuts (2) equally.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD CubCadet serie 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD CubCadet serie 2000 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD CubCadet serie 2000

MTD CubCadet serie 2000 User Manual - German - 19 pages

MTD CubCadet serie 2000 User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info