672424
11
Zoom out
Zoom in
Previous page
1/15
Next page
English Operating manual
8
Insert retaining bar (6) through
the openings (3, 4, 5) in order
to secure the gearbox.
While holding the retaining bar (6),
attach the cutting blade (7) with
blade holder (8), retaining bell (9)
and nut (10) as follows:
Push cutting blade (7) onto
drive shaft (2) and centre on
the spacer (1).
Note
Ensure that the cutting blade (7) is
seated correctly on the spacer (1),
i.e. centred and resting flat!
Attach blade holder (8),
retaining bell (9) and nut (10).
Ensure that the blade holder is
seated correctly in the toothing!
Tighten nut firmly anti-clockwise
(to the left) – tightening torque
37 Nm.
Note
Before tightening, check again that
the cutting blade is seated correctly.
If you do not have a torque wrench,
tighten the nut firmly by hand.
Then tighten the nut anti-clockwise
(to the left) another half turn using
a ring spanner.
Remove retaining bar from the
gear head.
Remove guard (if fitted) from
the cutting blade.
Removing the cutting blade
Fig. 8
Attach guard (if available) to the
cutting blade.
Align the openings (3, 4, 5).
Insert retaining bar (6) through the
openings and hold in position.
Unscrew nut clockwise (to the right).
Remove cutting blade (7), blade
holder (8) and retaining bell (9)
(Fig. 7).
Oil and petrol
Oil
Use quality oil only, API classification
TC (TSC-3) which is offered for air-
cooled two-stroke engines.
Mix the oil for two-stroke engines
according to the instructions on
the container, 1:40 (2.5 %).
Petrol
a~åÖÉê=
råÇÉê=ÅÉêí~áå=ÅçåÇáíáçåë=éÉíêçä=áë=
ÉñíêÉãÉäó=Ñä~ãã~ÄäÉ=~åÇ=ÉñéäçëáîÉK
Ó oÉÑìÉä=çåäó=áå=~=ïÉää=îÉåíáä~íÉÇ=~êÉ~=
~åÇ=ïáíÜ=íÜÉ=ÉåÖáåÉ=ëïáíÅÜÉÇ=çÑÑK=
aç=åçí=ëãçâÉ=~åÇ=ëïáíÅÜ=çÑÑ=~ää=
áÖåáíáçå=ëçìêÅÉë=áå=íÜÉ=îáÅáåáíó=çÑ=íÜÉ=
í~åâ=çê=~í=íÜÉ=ÑìÉä=ëíçê~ÖÉ=ÇÉéçíK
Ó aç=åçí=çîÉêÑáää=íÜÉ=ÑìÉä=í~åâ=EíÜÉêÉ=
ãìëí=ÄÉ=åç=ÑìÉä=áå=íÜÉ=áåäÉí=åçòòäÉFK=
^ÑíÉê=ÑáääáåÖ=ìé=íÜÉ=éÉíêçä=í~åâI=
ÉåëìêÉÜ~íÜÉ~åâ~éëäçëÉÇ=
~åÇ=ëÉÅìêÉÇK
Ó tÜÉå=ÑáääáåÖ=ìé=íÜÉ=éÉíêçä=í~åâI=Çç=
åçí=ëéáää=~åó=ÑìÉäK=péáääÉÇ=ÑìÉä=çê=
éÉíêçä=î~éçìêë=ã~ó=áÖåáíÉK=fÑ=ÑìÉä=
Ü~ë=ÄÉÉå=ëéáääÉÇI=ÉåëìêÉ=íÜ~í=íÜÉ=
~êÉ~=áë=ÇêáÉÇ=ÄÉÑçêÉ=íÜÉ=ÉåÖáåÉ=áë=
êÉëí~êíÉÇK
Ó mêÉîÉåí=êÉéÉ~íÉÇ=çê=éêçäçåÖÉÇ=
ëâáå=Åçåí~Åí=çê=áåÜ~ä~íáçå=çÑ=íÜÉ=
î~éçìêëK
`~ìíáçå
aççíáääéáíÜìÉäÑéÉÅáÑáÅ~íáçå=
bURK=fÑ=ÑìÉä=çÑ=ëéÉÅáÑáÅ~íáçå=bUR=
EÉíÜ~åçäçåíÉåí=[NR=BFëëÉÇIÜÉ=
ÉåÖáåÉ=ã~ó=ÄÉ=Ç~ã~ÖÉÇK=
qÜÉ=ìëÉ=çÑ=~å=ìå~ìíÜçêáëÉÇ=ÑìÉä=ïáää=
îçáÇ=íÜÉ=ï~êê~åíóK=
See instructions on mixing
oil and petrol
Age and/or incorrectly mixed fuel are
the main reasons for the unit not
running properly.
Always use clean, fresh unleaded
petrol (no more than 60 days old,
minimum octane number 91 ROZ).
Follow exactly the instructions for
the correct petrol/oil mixture.
Correctly mix two-stroke engine oil
and lead-free petrol, 1:40 (2.5 %).
Do not mix directly in the tank.
Fill the tank with petrol.
Fig. 1
Remove tank cap (4).
Fill fuel tank with petrol/oil mixture.
Never overfill!
Close fuel tank tightly.
Move the unit approx. 10 m from
the filling station/fuel container
before starting the engine.
Operation
a~åÖÉê=
aç=åçí=Üççâ=íÜÉ=ëÜçìäÇÉê=ëíê~é=çåíç=
íÜÉ=ìåáí=ìåíáä=íÜÉ=ÉåÖáåÉ=Ü~ë=ëí~êíÉÇK
Mix petrol (gasoline) with oil.
Fill the tank with the mixture.
See „Oil and petrol“.
Starting the engine
Starting the cold engine.
Fig. 9
Press throttle lock (2) and press
the throttle (3) all the way and hold
in position.
Move the ignition switch (1) to
the START position.
Release throttle lock and throttle.
Note
Both levers remain locked in the
depressed position (cold start
position).
Slowly and fully press intake
pump/primer (5) 6x (Fig. 10).
The fuel must be visible in the
pump. If this is not the case,
keep pressing until fuel is visible.
Move choke lever (6) to position
1/ (Fig. 11).
Press the unit on the ground.
Slowly pull on the starter cable (7)
until it begins to resist. Then pull
quickly and forcefully until the
engine starts (Fig. 12).
After starting the engine, do not let
the pull-starter spring back, but
slowly guide it back.
Leave the engine running for
approx. 1–2 minutes.
Move choke lever (6) to position
2/ and leave the engine to
warm up for another 1–2 minutes
(depending on the outside
temperature) (Fig. 11).
!
!
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD 1043 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD 1043 in the language / languages: English as an attachment in your email.

The manual is 2,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD 1043

MTD 1043 User Manual - German - 16 pages

MTD 1043 User Manual - Dutch - 16 pages

MTD 1043 User Manual - French - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info