481993

Moulinex Odacio Manual

17
Zoom out
Zoom in
Previous page
1/19
Next page
28
make any kinds of sausages.
ACCESSORIES USED
- Sausage funnel
(p)
, geared reducer
assembly
(n)
and mincer head
(o)
.
ASSEMBLY
- Fit the screws
(o3)
to the body
(o1)
of the mincer head metal.
- Place the funnel
(p)
then the nut
(o6)
and tighten fully.
- Place the assembled head onto the
geared reducer
(n)
.
Remark:
this accessory is used
without a disc or cutter.
USE
This accessory is to be used once the
meat has been minced and you have
seasoned the mince to your taste.
- After leaving the sausage skin to
soak in warm water so that it
becomes elastic again, slide it onto
the funnel
(p)
and leave
approximately 5 cm overhang.
- Fill the tube with mince
(o1)
, start
and press with the food pusher so as
to push the mince to the end of the
funnel.
- Stop the appliance.
- Make a knot 5 cm from the end of
the sausage skin. Slide it onto the
sausage funnel and push the knot
onto the end of the funnel to avoid
trapping air in the skin.
- Start the operation again and
continue to supply the mince. The
skin fills up.
- When all of the mince has been used,
stop the appliance, and remove the
remaining skin from the funnel and
make a knot.
Tips
To avoid the skin being too tight, do
not make sausages that are too big.
- It is easier when working with
someone else: one supplies the
mince and the other holds the skin
while it fills up.
- Make the sausages as long as you
want by pinching and turning the
skin at the desired lengths.
The speeds used are those of
paragraph 11.
BISCUIT NOZZLE
(depending on model)
This accessory which fits onto the
metal mincer head allows you to
make small biscuits.
ACCESSORIES USED
- Biscuit nozzle
(q)
, geared reducer
assembly
(n)
and mincer head
(o)
ASSEMBLY
- Fit the screws
(o3)
to the body
(o1)
of the metal mincer head.
- Place the mould
(q2)
in the support
(q1)
.
- Align the two support hooks
(q1)
with the two slots on the mincer
head
(o1)
.
- Tighten fully, without locking it, the
nut
(o6)
onto the body
(o1)
.
- Place this head assembly onto the
geared reducer
(n)
.
Remark:
this accessory is used
without a disc or a cutter.
USE
- Prepare the biscuit dough (you will
obtain better results with a soft
dough).
- Choose the pattern by aligning the
arrow with the chosen shape.
- Process until you have obtained the
quantity of biscuits desired.
Tips
The speeds used are those of
paragraph 11.
KEBBE ACCESSORY
(depending on model)
ACCESSORIES USED
- Kebbe accessory
(r)
, geared reducer
assembly
(n)
and mincer head
(o)
.
ASSEMBLY
- Fit the screws
(o3)
to the body
(o1)
of the metal mincer head.
- Place the nozzle
(r2)
on the head
aligning the two hooks with the two
slots on the mincer head.
- Place the ring
(r1)
on the nozzle
(r2)
then the nut
(o6)
and tighten fully.
- Place this head assembly onto the
geared reducer
(n)
.
Remark:
this accessory is used
without a disc or a cutter.
13
14
Moulf43 27/07/07 8:40 Page 29
… 17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Moulinex Odacio at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Moulinex Odacio in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info