744506

Morso 4412 Manual

17
Zoom out
Zoom in
Previous page
1/19
Next page
32
33
DK ENG
3.0 Routine stove maintenance
3.1 External maintenance
The cast surface of the stove is painted with heat-resistant Senotherm paint. It is best main-
tained by simply vacuuming it with a soft brush attachment or wiping it down with a dry,
dust-free cloth.
If the stove is used too vigorously, the painted surface may assume a greyish tinge over time,
but the stove can easily be freshened up with Morsø spray paint, which is available from your
local retailer.
Morsø stoves are painted using a Morsø Original Black (previously called Morsø dark grey)
or Morsø grey. The paint can be bought in a spray or a can.
3.2 Internal maintenance
Glass window
If the stove is used correctly, very little or no soot will be deposited on the ceramic glass
window. If soot does form on the glass as the stove is being lit, it will burn away once normal
combustion begins in the stove. If the glass window becomes thoroughly covered in soot
due to incorrect operation, the soot can be easily removed using Morsø Glass Cleaner. The
glass must be cold when you clean it. Avoid stoking the stove with pieces of wood that are
so long that they press against the glass window when the door is closed.
Only use Morsø Glass Cleaner.
Ceramic glass replacement
Ceramic glass cannot be recycled because it has a higher melting point that ordinary glass.
If ceramic glass is mixed with ordinary glass, the raw material is spoiled, and the reclaiming
process may be halted. Take care that the ovenproof glass does not end up among ordinary
recycled waste. That will be a great benet to the environment.
Note: Should be handed in to a recycling station as ceramic glass.
Internal cast-iron grate and/or wearing parts
The baes and other components that come in direct contact with the re and glowing fuel
are all wearing parts. As a result, they will be particularly susceptible to burn-through. When
used correctly, these parts will last for many years, but overly vigorous use will naturally ac-
celerate the burn-through. Such parts are all easily replaced. If the baes are damaged and
are not replaced in time, the top plate will be exposed to such high temperatures that it may
be damaged as well.
Reasons for sooty glass window:
- The fuel is too wet.
- The pieces of fuel are to big/uncut wood.
- The combustion temperature is too low.
- Insucient air for the combustion.
Reasons for overly rapid wear of internal parts
- Stove red too vigorously
- Use of very dry wood (wood from old furniture).
- Too much soot on top of the baes (please see the section on Cleaning).
- Too much ash in the ash pan (please see the section on Ash).
Please note that no unauthorised alterations of the design may be undertaken, and that
any parts that are replaced must be replaced with original Morsø parts.
Gaskets
Over time, the gaskets in the door will wear and should be replaced as needed in order to
prevent wild combustion. Use the original Morsø gasket kit.
Note: Normal wearing parts are not covered by Morsø’s extended warranty.
A selection of maintenance products (spare parts, glass cleaner, paint, gasket kit, etc.) is avail-
able from your Morsø dealer.
3.3 Cleaning the stove
In particular on the topside of the bae plates, layers of ashes and soot will form as a result
of the chimney draft and after a sweep.
The bae plates may be taken out of the stove under normal cleaning. When they are re-
moved, there is access to clean the ue chamber above the bae plates.
The bae plates are cleaned before they are reinserted, and care should be taken that they
are properly put in place.
Nowadays, the chimney sweep must remove the soot in the stove, in addition to sweeping
the chimney and cleaning the ue pipe. The number of annual sweepings/cleanings of the
stove should be determined in consultation with your chimney sweep.
Ash
As noted above, there should be a layer of approx. 1 cm insulating ash in the bottom of the
combustion chamber in order to achieve a high combustion temperature. If the layer of ash
is too thick, it can be brushed down into the ash pan.
Empty the ash pan before it gets completely full so that the ash does not insulate around
the grate, and thereby speed up the burn-through.
In most cases, the ash will need to be taken away by the waste disposal company. Because
embers may be concealed in the ash pan for several days, it may be necessary to store the
ash in a container made of non-ammable material before pouring it into a rubbish bag.
Ash from a wood-burning stove will not be of any benet to your garden as fertiliser. If you
have burned colour brochures, or painted or treated wood, etc., in the stove, the resulting
ash must not be poured onto soil as it may contain heavy metals.
… 17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morso 4412 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morso 4412 in the language / languages: English, Danish as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info