793838
4
Zoom out
Zoom in
Previous page
1/8
Next page
4
1
Using the iron
1) Filling the tank
Before first use, remove all packaging, including the protective cover on the soleplate. Make sure the iron is not
plugged in. Set the steam switch (6) to off. Fill the water tank (17) via the filling hole (13). To fill the tank with the
maximum amount of water, we recommend the iron is tilted approximately 45º whilst being filled.
Do not overfill the iron otherwise it will cause leaking from around the filler cap and may run down the iron.
WE RECOMMEND THE USE OF DEIONISED, DISTILLED OR DEMINERALISED WATER.
Never use battery topping up fluid or water containing any substances like starch, sugar, fragrant additives
or defrosted water from a refrigerator. NOTE: Please see point 2 of ‘Exclusions’ on page 8.
Plug in the charging base (10) and switch on at
the mains. The charging base indicator light (7)
will illuminate red.
Rest the iron on its heel (4) on the charging base,
ensuring that the heel connector (5) meets the
charging base connector (9). Connection is made
when the temperature indicator light (3) on the
handle illuminates red
.
Wait until the iron reaches
the desired temperature (see step 3), then
commence ironing.
Throughout your ironing session, the iron
must be replaced onto the charging base
every few seconds or whenever you adjust
your garments, to keep the heat topped up. If
the charging base indicator light (7) is fl
ashing
red, the iron must be replaced onto the
charging base until the red light turns green
again, then you can recommence ironing.
Set the temperature dial (16) to the temperature
required (see ‘Temperature Guide’ on page 3).
The charging base indicator light (7) and the
temperature indicator light (3)
will illuminate
red until the required temperature is reached,
then they will turn green.
NOTE: It is normal for the temperature indicator
light
(3)
to flicker between red and green whilst
the temperature cycles up and down during
charging.
Tip: We recommend the temperature indicator
light is allowed to cycle red and green twice
before you begin ironing.
The temperature indicator light
(3)
will extinguish
when the iron is removed from the base.
Tip: Begin with cool fabrics and work up to higher
settings. An iron heats up quicker than it cools
down so this will save you time and energy.
If required, switch on the steam using the steam
switch (6).
The amount of steam is automatically adjusted
to suit the temperature selected.
The iron will only produce steam when the
temperature is set within the steam quadrant on
the temperature dial (16), eg. if the 2 Dot setting
is selected, the iron will not steam.
For stubborn creases, use the water spray
button (1).
If using for the first time, you may need to press
this a few times to pull the water through.
2) Charging base 3) Temperature Selection
4) Switching on the steam 5) Using the water spray
RN303251MUK Rev1.qxp_Instruction Booklet 03/03/2021 09:29 Page 4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morphy Richards 303251 - easyCHARGE Power at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morphy Richards 303251 - easyCHARGE Power in the language / languages: English as an attachment in your email.

The manual is 3.59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info