33051
74
Zoom out
Zoom in
Previous page
1/76
Next page
74
Problem Possible Solution
1. The TV remote control does not work. • Check that the batteries are installed correctly.
• Check that the selected switch is set to “TV”.
• Be no further than 20 feet from the TV when using the remote control.
2. The TV takes several seconds to respond
to channel commands.
• Press ENTER after a channel number to avoid delays.
• Use the three digit number, i.e 002 for channel 2.
3. You cannot access a channel. • Use number keys instead of CHANNEL up/down.
• Be sure the channel you want to view is in memory.
• Check that the TV is turned to the correct input source for that
channel, by pressing the INPUT button.
• Make sure the V-Chip setting is Off (page 47).
4. On-screen displays appear each time you
change a function.
• This is part of normal TV operation.
5. The TV cannot be programmed to turn on
automatically.
• The TV may be locked.
• The clock may not be set.
6. There is no sound even when the volume is
turned up.
• Check to see if the MUTE button is on.
• The TVs “Listen to:” setting may be set to SAP.
• Check that “TV Speakers” setting is On.
7. • You have forgotten your lock passcode. • See Appendix A, Bypassing the V-Chip Lock (page 63).
8. Connected devices do not work correctly
when the TV is off.
• Energy Mode has been set to Low. Change to Standard (page 39).
9. PIP does not display a picture. • Make sure the V-Chip setting is Off (page 47).
• Not all inputs can be displayed as a PIP (page 22).
10. • The sound does not match the screen
picture.
• The TVs “Listen to:” setting may be set to SAP.
• If using stereo or A/V receiver speakers, check input selection on the
stereo or A/V receiver.
• If using stereo or A/V receiver, check that AUDIO is from MONITOR
OUT on TVs back panel.
11. • There is a large black or gray rectangle on
the screen.
• TV closed captioning has been set to “text” mode, but no text
information is being broadcast. Turn Off in the CAPTIONS menu
(page 40).
12. • Picture is out of focus, or colors are not
aligned.
• Adjust Convergence (page 53).
• Check the Sharpness settings (page 57).
13. • You cannot see a picture when you play a
VCR tape.
• If you connected your VCR with A/V cables, use the INPUT button to
select the Input source (INPUT-1, INPUT-2, or INPUT-3) that the VCR
is connected to.
• Check your VCRs owner’s guide for further troubleshooting.
14. There is no picture when using
MonitorLink/DVI input with an HDTV
receiver or DVD player.
• Make sure device is set to Output DVI in Device Menu.
• You may need to hook up to an analog input for initial setup.
15. • No picture displays when using component
inputs.
• Make sure device is set to output at 480p or 1080i via YPbPr or RGB
(check device output for compatibility).
16. • V-Chip is not working. • Make sure that V-Chip is On (page 47).
• If V-Chip Hours/Lock by Time is currently set to disable the
V-Chip lock, the V-Chip will not block programming.
17. • Cannot set adjustments to factory setting. • Follow the steps below to reset system defaults to factory settings:
1. Press the MENU button followed by number buttons 1,2,and 3 on
the remote control.
Result: The Reset System Default menu screen is activated.
2. Press the ENTER button on the remote control.
Result: The settings reset to factory defaults.
3. Press HOME or MENU on the remote control to return to the HOME
or MENU screen.
IMPORTANT: This function is not recommended unless it is mandatory
to reset system defaults to factory settings. This operation CANNOT
be undone and all customs settings will be erased.
Troubleshooting
Troubleshooting
74


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WT55315 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WT55315 in the language / languages: English as an attachment in your email.

The manual is 4,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info