588145
4
Zoom out
Zoom in
Previous page
1/5
Next page
2
5
1. If the AUTO mode is not comfortable , you may manually override
the settings by using COOL, DRY, HEAT( HEAT PUMP units only),
or FAN ONLY modes.
2. Push the or button to set the desired room temperature.
When in COOLING mode, the most comfortable settings are 21 C
or above. When in HEATING mode, the most comfortable settings
are 28 C or b elow.
3. Push the Fan button to select the FAN mode of AUTO, HIGH,
MED or LOW.
4. Push the On/off button. The operation lamp lights and the air
conditioner starts to operate per your settings. Push the On/off
button again to stop this unit operation.
The FAN ONLY mode cannot be used to control the temperature. While
in this mode, only steps 1 3 and 4 may be performed.
COOL , HEAT, and FAN ONLY Operation
NOTE
Due to the difference of the set temperature of the unit and the
actual indoor temperature, the Air Conditioner when in DRY mode
will automatically operate many times without running the COOL
and FAN mode.
1. Push the Mode button to select DRY.
2. Push the or button to set the desired temperature from
21 C to 2 8 C.
3. Push the On/off button. The operation lamp lights and the air
conditioner starts to operate in the DRY mode. Push the On/off
button again to stop this unit operation.
DRY OPERATION
NOTE
Push Timer on/off button to set the on and off times of the unit. The
effective operation time set by the remote controller for the timer function
is limited to a period of between 0.5 and less than 24 hours.
TIMER OPERATION
1. To set the STARTING time.
Button : Push the button to decrease the indoor temperature
setting to 17 .
Mode Button: Each time you press the button, a mode is
selected in a sequence that goes from AUTO COOL DRY
HEAT and FAN only as the following figure indicates:
Swing Button: Press the SWING button to activate the swing
feature. Push the button again to stop.
NOTE: HEAT only for Heat Pump
AUTO
COOL
DRY
HEAT FAN
Fan Button: This button is used for selecting Fan Speed. Each time
you press the button, a fan speed is selected in a sequence
that goes from AUTO LOW MED to HIGH, then back to Auto.
When you select the AUTO or DRY mode, the fan speed will be
automatically controlled and you can not set the fan speed.
Button : Push the button to increase the indoor temperature
setting to 30 .
1
2
3
4
5
6
7
8
9
On/off Button: Push this button to start the unit operation. Push
the button again to stop the unit operation.
Air direction Button: Press this button to change the swing
o
angle of the louver. The swing angle of the louver is 6 C for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button.
Timer on Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
Sleep/Turbo Button: Press this button to select SLEEP or TURBO
mode. Each time you press the button, the operation mode is shifted in
the direction of the arrow. When the operation mode is either DRY or
FAN only, this function can not be used.
1.1 Push the Timer on button, then the remote controller shows
ON TIMER , the last set time for the starting operation and the
signal "Hr" will be shown on the Timer display area. You
are now ready to reset the time to START the operation.
1.2 Push the Timer on button again to set desired unit start time.
1.3 After setting the Timer on ,there will be a one-half second
delay before the remote controller transmits the signal to
the air conditioner.
SLEEP
SLEEP OFF
TURBO TURBO OFF
10
Timer off Button: Press this button to initiate the auto-off time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10Hr, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, continue pressing the button
until nothing displays.
4


Need help? Post your question in this forum.

Forumrules
1

Forum

midea-r71a-remote-control

Reset search

  • how can i turn the timer completely off and turn the ac on and off freely whenever i want Submitted on 16-7-2023 at 19:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midea R71A Remote control at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midea R71A Remote control in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Midea R71A Remote control

Midea R71A Remote control User Manual - Dutch - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info