549237
1
Zoom out
Zoom in
Previous page
1/2
Next page
INSTALLATION MANUAL FOR ROOM
A
AIR CONDITIONER
(Split Wall-Mounted Type)
For correct installation, read this manual before starting installation.
Only trained and qualified service personnel should install, repair or service air conditioning
equipment. Users should not install the air conditioner by themselves.
All pictures are only sketches. If there is any difference between pictures in this manual and
the actual shape of the air conditioner you purchased, the actual shape shall prevail.
Installation in the following places may cause trouble. If it is unavoidable, please, consult
with the local dealer.
A place full of machine oil.
A saline place such as coast.
A place full of sulfide gas such as hot-spring resort.
Places where there are high frequency machines such as wireless equipment, welding
machine, and medical facility.
A place of special environmental conditions.
The appliance shall not be installed in the laundry.
A place, which is convenient to installation
and not exposed to a strong wind. A place
that is dry and ventilated.
A place can bear the weight of the outdoor
unit and where the outdoor unit can be held
in the horizontal position.
A place which does not allow an increase
in noise level and vibration.
A place where the operation noise and dis-
charge air do not disturb your neighbor.
A place free of a leakage of combustible
gases.
An allowable head level at the connective
piping is less than 5m and length of the
connective piping is up less than 10m.
No any obstacle which block radiat air.
Indoor Unit
Outdoor Unit
INSTALLATION PRECAUTION
A place where is no obstacle near the inlet
and outlet area.
A place which can bear the weight of the
indoor unit.
A place which allows the air filter to be
removed.
A place where the reception range is not
Exposed to direct sunlight.
A place where the connective pipe and
drain hose is easy to led out.
A place 1m or more to TV, radio instrument,
in the center of the room is perfect.
The indoor unit should be installed 2.3
meters or more above the floor.
INDOOR UNIT INSTALLATION
1
1. Run the drain hose sloping downward. Do
not install the drain hose as illustrated
below.
2. When connection extension drain hose,
insulate the connecting part of extension
drain hose with a shield pipe
Do not form a rise
Connective
pipe
Pipe holder
Pipe cover
Right piping
Left piping
Pipe cover
Drain hose
Connective
pipe
Pipe room
Ponding box
Indoor unit outline
Connective pipe
Right back piping
Left back piping
Wrapping belt
Do not put the hose
end into water
Indoor unit
1. For the left-hand and right-hand piping,
remove the rear plate bushing from the left
side of the rear plate.
Explain to clients that the pipe cover must
be kept as it may be used when relocate
the air conditioner to any other place.
2. For the left-hand and rear-left-hand piping,
install the piping as shown. Bend the conn-
ective pipe to be laid at 43mm height or
less from the wall.
3. Fix the end of the connective pipe.
(Refer to Tightening Connection in REFRI-
GRANT PIPING CONNECTION)
Connect the indoor unit first then the outdoor
unit and bend and arrange the pipe carefully.
Do not allow the piping to let out from the
back of the indoor unit.
Be careful not to let the drain hose slack.
Insulate both of the auxiliary piping.
Banding the drain hose under the auxiliary
pipe.
Do not allow the piping to let out from the
back of the indoor unit.
Wind the connective cable, drain hose and
wiring with tape securely, evenly as shown
below.
Because the condensed water from rare
of the indoor unit is gathered in ponding
box and is piped out of room. Do not put
anything else in the box.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
43
3. Piping and bandaging
1. Drainage
2. Connective pipe
CAUTION
1. Drilling A Hole and Mounting Installation Plate
2. Connective Pipe and Drainage Installation
Installation Plate and Its Dimention
Indoor unit outline
20
12cm or more
to wall 12cm or more
to wall
Left refrigerant
pipe hole 65 Right refrigerant
pipe hole 65
Installation plate
30
70
750
45
250
15cm or more to ceiling
1. Install the installation plate horizontally on stru-
ctural parts in the wall with the spaces provided
around the plate.
2. In case of brick, concrete or similar type walls,
make 6mmdia, holes in the wall. Insert clip anc-
hors for appropriate mounting screws.
3. Fix the installation plate on the wall.
1. Pass the piping through the hole in the wall.
2. Put the upper claw at the back of the indoor unit on
the upper hook of the installation plate, move the
indoor unit from side to side to see that it is securely
hooked.
3. Piping can easily be made by lifting the indoor unit
with a cushioning material between the indoor unit
and the wall. Get it out after finish piping.
4. Push the lower part of the indoor unit up on the wall,
Then move the indoor unit from side to side, up and
down to check if it is hooked securely.
1. As diagram above determine the pipe
hole position using the installation
plate, drill the pipe hole( 65mm) so it
slants slightly downward.
2. Always use a wall hole conduit when
piercing metal lath, ply wood or metal
plate.
Upper hooker
Low hooker
Cushioning
material
Installation Plate
1. Fix the installation plate.
2. Drilling a hole.
3. Indoor Unit Installation
.
.
.
...
.
.
.
.
.
.
.
.
.
.
.
.
...
.
...
.
.
.
.
.
. .
.
NOTE: At least two of A, B, C
Aspects are free from blocking.
60cm or more
Air blowing
direction
Loop the
connective
cable.
Air filter
12cm or more
12cm or more
15cm or more
10cm or more
100cm or more
3
2
1
4
C
A
B
Before installation, operate the remote
controller to determine its location in a
reception range.
Keep the remote controller at least 1m
apart from the nearest TV set or stereo
equipment.
Do not install the remote controller in a
place exposed to direct sunlight or close
to a heating source, such as a stove.
Note that the positive and negative poles
are right positions when loading batteries.
The air-conditioner can be connected only
to a supply with system impedance no
more than 0.26 ohm. In case necessary
please consult your supply authority for
system impedance information.
Part
No.
1
2
3
4
5
6
7
8
Installation plate
Mounting screw ST3.9 25-C-H
Refrigerant
pipe
Liquid side
Gas
side
Remote controller
Remote controller holder
Seal
Drain elbow
6.35
9.53
1
8
8
1
1
1
1
Name of part Qty
Parts Installation
Cautions on remote controller installation
10cm or more
60cm or more
5
6
Clip anchor
anchor bolts of out door unit installation
The outdoor unit should not be exposed to
strong wind.
Fix the outdoor unit with 10 or 8 anchor
bolts.
air outlet
air inlet
A
B
Remote controller
Mounting screw B
ST2.9x10-C-H
Remote controller
holder
12.7
10000Btu/h
9000Btu/h
Model
7000Btu/h
9000Btu/h
50Hz R22
9000Btu/h
60Hz R22
9000Btu/h
R407C
10000Btu/h
A
458
548
548
548
458
B
250
266
266
266
250
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midea Glory Eco MSG-xxHRN2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midea Glory Eco MSG-xxHRN2 in the language / languages: English as an attachment in your email.

The manual is 0,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Midea Glory Eco MSG-xxHRN2

Midea Glory Eco MSG-xxHRN2 User Manual - English - 12 pages

Midea Glory Eco MSG-xxHRN2 User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info