658470
129
Zoom out
Zoom in
Previous page
1/666
Next page
About the patching procedure 89
PRO Series Live Audio Systems
Owner’s Manual
>> To select the list tooltip
Press LIST. (Pressing LIST again will change the tooltip back to the standard type.)
About the patching procedure
Although patching can be thought of as routing/rerouting the control centre’s incoming,
internal and outgoing signals, in the context of the Patching screen, patching also
encompasses the setting up and configuration of the stage and FOH rack I/O devices.
The patching procedure is initially carried out after system installation and comprises:
Device configuration Configure the devices by adjusting their parameters (see
below).
Snake selection Configure the control centre according to the type of ‘snake’ you
are using for the X and Y networks (see “Configuring the snake type” on page 92).
This is important, as the control centre will not work unless the snake type
is correctly configured.
Setting up the I/O rack devices Set up the system devices, such as line I/O,
DN9696 and generic AES50, in the I/O tabs in the From and To sections of the
Patching screen (see “Setting up the I/O rack devices” on page 92).
Patching Carry out all of the required routing, for example, mics to input channels
(see “How to patch” on page 94).
Configuring the devices
You have the option to configure the devices from the Patching screen. Parameters,
such as gain and +48V phantom voltage, can be adjusted or switched on/off,
respectively, via a device-specific configuration window.
These configuration settings can be independent of channel data, as (until patched)
they only control the physical unit. If a device is subsequently patched to one or more
channels, the channel(s) control the device, and vice-versa.
The device configuration area also allows control of audio parameters when the device
is used as a direct connection to another device. For example, FOH to stage via a
digital snake, instead of through the DSP. In this case the settings are also saved in the
show file and can be automated, even though the signals are not routed through the
control centre DSP.
Item Description
1 ID of the patch connector belonging to the tooltip. If selected, this patch
connector will be patched to the source patch connector at the bottom of
the list.
2 List of selected sources still to be patched. Contains channel and device ID
information.
3 This source patch connector is the one waiting to be patched. Once
patched, this will disappear from the list and the one immediately above will
take its place.
129

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midas PRO9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midas PRO9 in the language / languages: English as an attachment in your email.

The manual is 30,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info