600617

Metabo SSE 1100 Manual

10
Zoom out
Zoom in
Previous page
1/68
Next page
ENGLISHen
10
hands. Therefore always hold the machine with
both hands using the handle provided, stand
securely and concentrate.
7.4 Working Directions
Sawing:
Use a saw blade geared to the material to be sawn.
SSEP 1400 MVT: Set pendulum motion according
to the applications.
Adapt the stroke rate to the material to the sawn.
SSEP 1400 MVT: Set maximum stroke rate
according to the applications.
Press the machine with the guide (9) against the
workpiece. Switch on the machine, and only then
guide the saw blade against the workpiece.
Do not make contact with any objects or with the
ground with the moving saw blade (danger of
recoil!)
Avoid excessive pressure on the saw blade
(particularly in the case of long saw blades).
If the saw blade jams, turn the machine off
immediately. Widen the sawn gap slightly with a
suitable tool and take out the machine.
After completing the sawing cut, switch off the
machine and only take it out of the sawn gap to
place it down once the saw blade has come to a
standstill (danger of recoil).
Plunge cuts:
Plunge cuts may only be made in soft materials
such as wood or plastic. Only use short saw blades.
Hold the machine with both hands at the intended
handles, take a secure stance and concentrate on
the work.
Set the adjustment lever (4) to the "0" position
(pendulum motion is deactivated).
See illustration B, page 2:
The machine is pressed with the edge of the guide
(9) against the workpiece. The saw blade does not
make contact with the workpiece. Switch on the
machine. The corner of the guide serves as a pivot
point around which the machine is slowly aligned,
whereby the saw blade cuts into the workpiece.
7.5 Sawing close to the wall
Set the adjustment lever (4) to the "0" position
(pendulum motion is deactivated).
See illustration D, page 2.
When sawing near the wall, the saw blade can be
put into the saw blade clamping fixture with the
teeth pointing upwards (contrary to the normal
working position). Ensure that the pendulum action
is deactivated.
To saw tight curves: Use narrow saw blades.
Sawing metal: To increase the life of the saw
blades, apply cooling lubricant (cooling lubricant
rod 6.23443) along the cutting line.
On a regular basis, use compressed air to blow out
the machine through the rear ventilation slots.
Regularly clean the saw blade quick-clamping
fixture (2) and blow out with compressed air. Do not
oil or grease.
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
See www.metabo.com or the catalogue for a
complete range of accessories.
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2002/96/EC
on waste electrical and electronic equipment and its
implementation in national legal systems.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P
1
=Rated input power
P
2
=Power output
I=Current
n
0
=Stroke rate at idle speed
s=Stroke length
m =Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~ AC Power
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
8. Tips and Tricks
9. Maintenance
10. Accessories
11. Repairs
12. Environmental Protection
13. Technical Data
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo SSE 1100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo SSE 1100 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info