494961
30
Zoom out
Zoom in
Previous page
1/34
Next page
Tr o u b l e s h o o t i n g
2 6
Processor operation
The LCD is displaying an OVERHEAT WARNING.
The DVP-1080 processor possesses thermal protection circuitry which actively monitors
internal temperature during operation. Excessive heat may cause the processor to
malfunction, and/or, shorten product lifespan.
Do not mount processor above power amplifiers or other equipment which generate
excessive heat
Allow a minimum of one rack space, above and below the unit, for proper ventilation
(1RU or 1.75”).
Insure there is adequate system rack ventilation (preempts failure with additional
installed equipment)
LEVEL 1 WARNING / HIGH TEMPERATURE
Internal Temperature is exceeding safe operational limits. Steps should be taken to improve
ventilation
LEVEL 2 WARNING / HIGH TEMPERATURE
Internal Temperature is at critical thermal limits; processor failure may occur. Immediate
steps should be
implemented, to improve ventilation, and return the unit to optimal operational
temperature
LEVEL 3 WARNING / EXTREME TEMPERATURE
Internal Temperature has exceeded maximum thermal limitations; processor will shut down.
A LEVEL 3 WARNING will only display for Five (5) Seconds, then the DVP-1080 will shut
down
DVP-1080 cannot be powered ON by the front panel power button during this condition
A LEVEL 3 WARNING indication requires the unit first be unplugged to reset
Normal operation resumes once the DVP-1080 has returned to optimal thermal
temperature
How do I Store a Profile?
A stored PROFILE is merely a “Snap-Shot-In-Time” for all settings which have been selected
from both the SETUP MENU options (LCD), or the USER MENU (OSD) options, within the
DVP1080 processor, and programmed into the processor’s CPU.
System SETUP MENU Option (LCD)
Enter the SETUP MENU by pressing
Menu on the IR remote for seven seconds
Select all applicable changes required for the intended PROFILE within the SETUP MENU
Press
Menu to exit the SETUP MENU
Then, proceed to…
On-screen USER MENU Options (OSD)
Press
Menu to view the On-Screen Display (OSD)
Adjust all applicable changes required for the intended PROFILE
Under the menu tab INPUT, use
V to highlight PROFILE
Press the
> to select numeric PROFILE
Press
Store.
Press
Menu to exit the On-Screen Display.
When I select 4:3 on the IR remote, the image is not centered
This essentially means the innate 16:9 image from the DVP-1080, when selecting
ANAMORPHIC, is not properly centered on the display device.
Utilize a DVD ‘Screen Area’ test pattern (DVD Essentials, AVIA, etc.)
Center, and position the image for a 2.5% over-scan, using the displays sizing and
positioning controls.
Once the image has been properly centered, sized and positioned (utilizing the display
controls), the 4:3 image will fall-in-to-place and be centered within the 16:9 display
area.
Note: Do not view a 4:3 images for prolonged periods of time on a 16:9 display; image
Burn-In may occur. Image Burn-In is not covered under the warranty.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Meridian DVP 1080 HD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Meridian DVP 1080 HD in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info