Manual Meliconi universal 4 (page 2 of 6) (English)

122407

Zoom out

Zoom in

1/6

SET-UP

Read these instructions

carefully before programming

your remote control!

MAKE SEARCH PROGRAMMING MODE

1.Turn ON the appliance:

– if a VCR, insert a cassette

– if SAT, select a program

– if DVD, insert a DVD.

2. In the code book enclosed, look for the

make of your appliance and make a

note of the code indicated at the side

(e.g. Philips 001) or the code for the

make indicated by the arrow.

3.Press and release the TV - VCR - SAT -

DVD selection button for the appliance

you want to use:

– the TV button is used to search only

for the TVs of the make selected

– the VCR button is used to search only

for the VCRs of the make selected

– the SAT button is used to search only

for the SATs of the make selected

– the DVD button is used to search only

for the DVDs of the make selected.

4. Hold down the SHIFT and ON/OFF

buttons together until the TV - VCR -

SAT - DVD selection buttons

start to flash indicating that the

remote control is programming.

5. Release the buttons. Within 15

seconds, enter the make code

previously identified (e.g. 001).

The TV- VCR - SAT -DVD selection

button flashes more quickly to indicate

that the remote control is ready for the

search.

6. Point the remote control at the

appliance. Press and release one of

the most frequently used keys several

times STOPPING when the appliance

responds correctly to the command.

7. When the appliance responds

correctly, press SHIFT to confirm.

Three flashes indicate that the

operation has been completed

correctly.

Identify and make a note of the code

for the appliance which you have

searched for following the code

noting procedure (see “NOTING THE

PROGRAMMED CODE” section).

Warning: program one appliance at a time.

SHIFT

FITTING THE BATTERIES

Before programming and using the remote control, fit the batteries.

The remote control requires 2 new AAA/LR03 alkaline batteries.

Insert the batteries as shown.

• The batteries must be changed once a year.

• If the TV - VCR - SAT - DVD/ selection buttons start

to flash during use, this indicates that the batteries

are low and should be changed.

• When you remove the batteries, fit the new ones

within 5 minutes or you may have to reprogram your

remote control.

• Make a note of the codes for the TV - VCR - SAT -

DVD equipment on the adhesive label inside the

battery cover. This note will be handy if you have to

reprogram your control.

DVD

SAT

VCR

NOTE: THE SELECTION BUTTON

STOPS FLASHING.

The remote control leaves the

programming mode and the

TV - VCR - SAT - DVD selection

button stops flashing:

•

if no buttons are pressed for 15 seconds

•

if an invalid make code is entered

•

if the code search list is completed. In

this case, go back to point 3 or switch to

programming mode C

•

if you press the TV - VCR - SAT - DVD -

F1 - F2 - F3 - F4 buttons by mistake.

To program the Universal 4 remote

control, follow the indications

in section A , B or C .

Please iam using Humax decoder what is my three code I can not find it Submitted on 10-8-2020 at 22:08
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Meliconi universal 4 in the language / languages: English as an attachment in your email.

The manual is 0,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Meliconi universal 4 Manual

Product: