Manual ME VDV 505 (page 7 of 16) (English, German, Dutch, French)

568559

Zoom out

Zoom in

1/16

ENGLISH | VDV505

release button. A double beep on the external and indoor unit conﬁrms

the door has been released and the green name plate also lights up

green if the door release mechanism is activated.

The door release mechanism can be activated if:

1. somebody rings the doorbell (within 60 seconds and without having

to establish voice communication ﬁrst);

2. the reply function is on.

Set the doorbell chime

1. Press the speak button (monitor switches on).

2. Press the chime button to play the chime set.

3. Press the chime button to play the next chime and repeat this

process until you ﬁnd the chime you want.

4. Press the speak button to save the chime (monitor switches off).

There are 12 different chimes to choose from.

Set the handset volume

Use the handset volume control on the side of the indoor unit to

inﬁnitely adjust the handset volume of the person at the other end.

Set the doorbell volume

The volume can be inﬁnitely set between 0% and 100% using the

doorbell volume control on the mainboard (adjust the volume with

a small screw driver; turning clockwise to increase the volume and

anticlockwise to decrease it).

Be careful not to overtighten the potentiometer.

Disable the doorbell chime (e.g. at night)

The doorbell chime can be disabled. To do this, press the sleep button

on the indoor unit once. The LED below the sleep button ﬂashes red to

show that the chime has been disabled. To activate the chime again,

press the sleep button again; the LED will stop ﬂashing and the chime

will be reactivated.

The optical signal (light surrounding the speak and door release

buttons) remains activated even if the doorbell chime is disabled and

continues to indicate that the doorbell has been pressed.

NOTE: If the VTX-BELL module is used, this will also be

disabled during sleep mode, i.e. the signal from connected

receivers is also disabled.

Activate alarm

The external station can sound an alarm (e.g. if you are being

harassed). To do this, you have to press and hold the alarm button on

the indoor unit. The alarm only sounds if the button is pressed and

held down within 60 seconds after the doorbell was pressed or if voice

communication is established.

Intercom

If several indoor units are connected in parallel, you can communicate

between these indoor units.

If you press the alarm button when the station is on standby, all indoor

units connected in parallel will sound the alarm. Voice communication

is established if the handset is lifted on one of the ringing indoor units

or the speak button is pressed. To end the call, either put the handset

down or press the speak button.

Activate the monitor / switch through additional cameras

The monitor button allows you to monitor the entrance area at any time

without somebody having to press the doorbell. Pressing the monitor

button a second time turns it off.

NOTE: If an additional camera (model: VD 500 XCam) or several

external stations are connected, these can be activated using the

monitor button. Pressing the monitor once activates the external station

camera, pressing it a second time turns on the ﬁrst additional camera

and pressing it a third time turns on the second additional camera. If

all the cameras are switched through, you can see the image from the

ﬁrst camera. You can only disable the monitor by double pressing the

speak button or wait approx. 60 seconds until the system automatically

returns to standby mode.

Adjust monitor brightness

You can use the brightness button to adjust the monitor brightness to

seven levels. Each time you press the brightness button, the brightness

level increases; the brightness returns to the lowest level when it

reaches level seven.

Adjust the monitor contrast

You can use the contrast button to adjust the monitor contrast to seven

levels. Each time you press the contrast button, the level increases; the

contrast returns to the lowest level when it reaches level seven.

Adjust the colour saturation of the monitor

You can use the colour saturation button to adjust the monitor colour

space to seven levels. Each time you press the colour saturation button,

the level increases; the colour space returns to the lowest level when it

reaches level seven.

TECHNICAL DATA

Operating voltage: 15 V DC

Current consumption: 220 ± 50 mA

Temperature range: -10°C to +50°C

Maximum humidity: 85%

INFORMATION

Information regarding CE - Conformity

The functionality of the unit can be affected by the inﬂuence of strong

static, electrical or high frequency ﬁelds (discharging, mobile phones,

radios, microwaves).

Cleaning and maintenance

Always disconnect mains powered units from the mains supply before

cleaning (disconnect the plug). The unit housing can be cleaned using

a soapy soft cloth. Do not use any abrasive materials or chemicals.

Remove dust build-up from ventilation slits using a brush and clean up

using a vacuum cleaner. Do not hold the vacuum cleaner nozzle directly

against the unit.

Safety instruction

In the event of damage to the housing, connectors, power cables or

isolation shielding, switch off the device immediately and disconnect

from the mains power.

ELECTRIC SHOCK – DANGER OF LOSS

OF LIFE. (Unplug the mains connector from the socket!). Damage

should be repaired immediately by a specialist!

Never carry out repairs yourself!

VDV-505_I-Manual_Fin2+3mm.indd 7 27.06.12 12:15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ME VDV 505 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ME VDV 505 Manual

Product: