478442
13
Zoom out
Zoom in
Previous page
1/15
Next page
ENGLISH - 10
and lower cut. The meeting point between the two
sides of the notch is called “directional cut line” This
line must be perfectly horizontal at right angles (90°)
to the felling direction.
The felling cut that provokes the tree fall, is performed
at 3 to 5 cm above the lower part of the directional
felling cut line, finishing at a distance of 1/10 of the
trunk from the notch. Remain on the left hand side of
the tree and cut using the chain pulling method and
the spiked bumper. Check that the tree does not
move in a direction other than that predicted for the
fall. As soon as possible insert a felling lever or
wedge into the cut. The uncut part of the trunk is
called the “hinge”, as it is intended to guide the tree
as it falls; in cases where the cuts are not sufficient,
not straight, or have been cut through completely, the
tree fall cannot be controlled (extremely dangerous!).
For this reason the various cuts must be performed
with great precision.
When cutting operations are completed the tree will
begin to fall. Where necessary help tree fall using
wedges or felling levers
.
Limbing
Once the tree has been felled, the trunk must be
limbed: in other words, the branches are removed
from the trunk. Do not underestimate this operation
because the large majority of kickback accidents
occur during this stage. For this reason pay close
attention to the position of the bar nose during cutting
operations and always work on the left hand side of
the trunk.
I. ENVIRONMENTAL INFORMATION
This section contains information useful for maintaining the characteristic of ecocompatibility included in the
origin design of the machine, and as regards proper use and disposal of chain oil
DESIGN
In the design stage, care was taken to develop an engine with reduced consumption and low emission of noise.
USE OF THE MACHINE
The operations of filling the oil tank should be carried out in such a way as to avoid spilling oil and contaminating
the soil and the environment.
DISPOSAL
Do not dispose inappropriately of the machine when it is no longer usable. Deliver it to an authorized
organization for proper disposal in compliance with the regulation in force.
The symbol
on the product or on its packaging indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product, please contact your local
council office, your household waste disposal service or the shop where you purchased the product.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch EL1640 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch EL1640 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info