590551
10
Zoom out
Zoom in
Previous page
1/12
Next page
Cutting techniques
During the cutting operations, keep the
engine running at high speed. After every
cutting stage, decelerate the engine to minimum
speed as running it at top speed without a load
can damage the engine severely.
Wait until the engine is running at minimum
speed before moving the machine from one
section to another.
The machine is ideal to complete the work of the
lawnmover. In fact, it can reach places where a
ENGLISH - 7
G. Carburetor adjustment
Your machine can be equipped with a low emis-
sion carburetor. We recommend that you have
any adjustment of the carburetor made exclusive-
ly by an authorized service center, which disposes
of special equipment for ensuring the best per-
formance with the lowest emissions. To adjust the
speed to the minimum, turn the screw marked (T)
as shown: With the engine running and well
warmed up, turn the screw (T) gently clockwise,
until the engine rotates at regular speed (stead
noise), without the cutting devices in motion. If
the cutting devices are moving, turn the screw (T)
gently counterclockwise until you obtain the prop-
er adjustment. The correct minimum speed is
shown in the instruction manual in the paragraph
of technical data.
All the above adjustments should be made
with the cutting devices correctly installed.
The warranty may be invalidated due to erro-
neous adjustments made by personnel not
belonging to authorized service centers.
8 9 10 11
H1. After every use
In order to avoid overheating the motor, remove
any dust and dirt from the slots on the cylinder
cover and finds of the cylinder using a wooden
scraper. Store the machine in a dry place.
After 25 hours of use
Remove the filter as shown in the figure and clean
it using a gentle jet of compressed air. For more
thorough cleansing, you can wash it with soapy
water.
After 50 hours of use
Add some high speed gear grease in the gearbox
through hole (C). Remove and clean the spark
plug (set the space between the electrode at
0.5/0.6 mm). Replace if excessively encrusted. In
case of excessive encrustation check the carbu-
retor adjustment, the percentage of oil in the fuel
mixture and make sure the oil is of excellent quali-
ty and suitable for two-stroke engines.
After 100 hours of use
Replace the spark plug.
Every three months
Contact your Service Center for a complete over-
haul, replacement of the fuel filter and cleaning of
the parts inside the machine. This will reduce the
possibility of unexpected problems and will
ensure the good performance and long life of
your machine.
Periods of prolonged disuse
See "Environmental information".
If you use the machine in an exceptionally
dirty or dusty environment these operations
should be carried out more often.
H2. Replacement of nylon string
To replace the reel of string, press both the
release pawls indicated by the arrows, remove
the empty reel, unroll any string left and rewind
the new string. Open the original package of
string and insert the ends of the two strings in the
eyelets on the reel, then wind the strings com-
pletely on the reel in the same direction and fas-
ten the end of each string in the 2 opposite
grooves. Replace the reel in its housing and
thread the ends of the strings in their bushings.
Pull each string so that about 15 cm comes out
on each side. Reassemble the nylon string head
as shown. If the reel becomes excessively worn,
replace it with a whole new reel.
H3. Attachments maintenance
Follow maintenance instructions on the attach-
ment manual.
H. Routine maintenance
1 2 3 4 7 9 10 17
I. Techniques for use
1 4 5 6 7 8 9
10 11 12 13 14 16 17
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch Cabrio Plus 407 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Cabrio Plus 407 in the language / languages: All languages as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info