1. Druk op Mode (indien nodig meermaals) tot ODO verschijnt
2. Druk Set/Reset gedurende 2 seconden
3. Druk Set/Reset voor de cijferaanduiding
4. Druk Mode om over te gaan naar het derde cijfer, herhaal stap 3
5. Druk Mode om over te gaan naar het tweede cijfer, herhaal stap 3
6. Druk Mode om over te gaan naar het eerste cijfer, herhaal stap 3
7. Druk Mode en selecteer Km/h of Mile/h met Set/Reset
Uw teller zal de configuratie toestand na 3 seconden verlaten indien u geen toetsen
meer bediend.
B. Instellingen van de tijd
1. Druk Mode indien nodig meermaals tot het symbool van een uurwerk verschijnt
2. Druk Set/Reset voor 2 seconden
3. Druk Set/Reset om de minuten aan te duiden
4. Druk Mode om over te gaan naar uren
5. Druk Set/Reset om de uren aan te duiden
Uw teller zal de configuratie toestand na 3 seconden verlaten indien u geen toets
meer bediend.
C. Gebruik de toets Mode om te navigeren tussen de verschillende schermen
D. Gebruik van de chronometer
1. Druk Mode indien nodig meermaals tot het symbool chronometer verschijnt
2. Druk Set/Reset om de chronometer te starten of te stoppen
E. Volgende waarden kunnen terug op nul gezet worden door gedurende
2 seconden Set/Reset te drukken Tijd(TM),afstand(DST),gemiddelde (AVS),
maximum(max),calorieën(cal)
F. Reiniging en onderhoud
Gebruik een zachte, licht vochtige doek(water)
H. Veiligheid
Alle elementen moeten correct bevestigd worden op uw fiets
om ongelukken te vermijden.
Installation du capteur (fig.2)
Installation du support (fig.1)
A
A
B
C
D
E
F
G
A. Presser pour enlever le compteur du support
B. Vis de fixation du support
C. Faire glisser le compteur dans le support
D. Levier
E. Câble du capteur
F. Rondelle en caoutchouc
G. Guidon
cycle computer
B
C
D
F
G
H
I
J
K
E
A. Fourche
B. Câble du capteur
C. Rayon de la roue
D. Vis de blocage de l’aimant
E. Aimant
F. Distance aimant-capteur
G. Colson
H. Caoutchouc de protection
I. Colson
J. Alignement aimant-capteur
K. Fourche
A. Réglage de la taille de la roue:
Mesurer la circonférence de votre roue en mm
1. Appuyez sur le bouton “MODE” (plusieurs fois si nécessaire) pour afficher “ODO”
2. Maintenez sur le bouton “SET/RESET” environs 2 secondes
3. Appuyez sur le bouton “SET/RESET” pour indiquer le chiffre
4. Appuyez sur le bouton “MODE” pour passer au 3ème chiffre et répéter l’étape 3
5. Appuyez sur le bouton “MODE” pour passer au2ème chiffre et répéter l’étape 3
6. Appuyez sur le bouton “MODE” pour passer au premier chiffre et répéter l’étape 3
7. Appuyez sur le bouton “MODE” et sélectionner Km/h ou Mile/h
avec le bouton “SET/RESET”
Votre compteur sortira du mode configuration après 3 secondes
si vous n’appuyez sur aucuns boutons.
B. Réglage de l’heure:
1. Appuyez sur le bouton “MODE” (plusieurs fois si nécessaire) pour afficher le
symbole “horloge”
2. Maintenez sur le bouton “SET/RESET” environs 2 secondes
3. Appuyez sur le bouton “SET/RESET” pour indiquer les minutes
4. Appuyez sur le bouton “MODE” pour passer aux heures
5. Appuyez sur le bouton “SET/RESET” pour indiquer les heures
Votre compteur sortira du mode configuration après 3 secondes
si vous n’appuyez sur aucuns boutons.
C. Utilisez le bouton “MODE” pour naviguer dans les différents modes du compteur
D. Utilisation du chronomètre:
1. Appuyez sur le bouton “MODE” (plusieurs fois si nécessaire) pour afficher le
symbole “CHRONOMETRE”
2. Appuyez sur le bouton “SET/RESET” pour démarrer et arrêter le chronomètre.
E. Les valeurs suivantes peuvent être remises à zéro en en appuyant 2 secondes
sur le bouton “SET/RESET”: Temps (TM), Distance (DST), Moyenne (AVS),
Maximum (MAX), Calories (CAL).
F. Nettoyage et entretien : utiliser un chiffon doux légèrement humidifié avec de l’eau.
G. Sécurité: les éléments doivent être correctement fixés à votre vélo pour éviter tout
risque d’accident.
INSTRUCTIONS DE MONTAGE ET MODE D’EMPLOIINSTALLATIE EN GEBRUIKSAANWIJZING
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Maxxus Quadra at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Maxxus Quadra in the language / languages: Dutch, French as an attachment in your email.
The manual is 0,53 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.