506269
2
Zoom out
Zoom in
Previous page
1/28
Next page
MAX 5073
Super Bass System
MOUNTING YOUR AMPLIFIER
The mounting position of your Amplifier will have a great effect on its ability to dissipate the heat
generated during normal operation. It has an ample heat sink for heat dissipation, and is also design-
ed with a thermal shut-down protection circuit, making it reasonably tolerant of mounting variations.
Any configuration which allows moving air to be directed over the cooling fins will improve heat dis-
sipation dramatically. DO NOT enclose the amplifier in a small box or cover it so that air cannot flow
around the heat sink fins.
Temperatures in car trunks have been measured as high as 175 F (80 C) in the summer time. Since
the thermal shut-down point for the Amplifier is 185 F (85 C), it is easy to see that it must be moun-
ted for maximum cooling capability. To achieve maximum advantage of convection air flow in an
enclosed trunk, mount the amplifier in a vertical position, on a vertical surface.
Cooling requirements are considerably relaxed when mounting inside the passenger compartment
since the driver will not often allow temperatures to reach a critical point. Floor mounting under the
seat is usually satisfactory as long as there is at least 1 inch (2,5cm) abo
ve the Amplifier’s fins for
v
entilation.
a. Select a suitable location that is convenient for mounting, is accessible for wiring, and has ample
room for air circulation and cooling.
b. Use the amplifier as a template to mark the mounting holes. Remove the Amplifier and drill 6 holes.
USE EXTREME CAUTION, INSPECT UNDERNEATH SURFACE BEFORE DRILLING.
c. Secure the Amplifier using the screws provided.
CONNECTING THE POWER
CAUTION! AS A PRECAUTION. IT IS ADVISABLE TO DISCONNECT THE VEHICLE’S BATTERY BEFORE
MAKING CONNCETIONG TO THE+12 VOLT SUPPLY WIRING.
10GAUGE (or a large gauge of wire if planning for additional Amplifiers) wire is recommend the power
and ground wires. 20 Gauge, for the remote turn-on wire. Both types are a
v
ailable at most Mobile
A
udio Dealers or installation Shops.
GROUND T
o V
ehicle Chassis
T
o avoid unwanted ignition noise caused by ground loops, it is essential that the Amplifier be groun-
ded to a clean, bare, metal surface of the vehicle’s chassis.
NOTE: GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT.(1 METER)
USING THIS METHOD CAN CAUSE TURN ON AND TRUN OFF TRANSIENTS (NOISE)
+12 Volt (Fused)Constant Power: To Battery (+)
Due to the power requirements of the Amplifier, this connection should be made directly to the posi-
tive (+) terminal of battery. F
or safet
y measures, install an in-line 50 Amp Fuse Holder(not
included)as close to the battery positiv
e (+) terminal as possible, with an ampere rating not to exceed
the total value of fuses in amp.
Remote Turn-On Input: T
o P
ower Antenna output of Car Stereo
This Amplifier is turned “ON” remotely when the vehicle’s stereo is turned “ON”.
NOTE: IF YOUR RADIO DOES NOT HAVE A +12 VOLT OUTPUT LEAD WHEN THE RADIO IS TURNED
ON, “RMT” TERMINAL ON THE AMPLIFIER CAN BE CONNECTED TO VEHICLE’S ACCESSORY CIRCUIT
THAT IS LIVE WHEN THE KEY IS “ON”.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MaxGear MAX 5073 super bass system at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MaxGear MAX 5073 super bass system in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info