785570

Mastervolt MasterBus LIN Bus Interface Manual

3
Zoom out
Zoom in
Previous page
1/4
Next page
LIN Interface – User and
Installation Manual
3
Steps:
1. Mount the LIN Interface to any flat surface. The LIN Interface comes with
a DIN rail mount option. Alternatively, use the two mounting holes (1).
2. Wire the screw terminal (2).
a. LIN Battery +
b. LIN Bus Line
c. LIN GND
Make sure that the power cable is fused with a 1A fuse.
3. Insert the MasterBus cable (included, 1m) to integrate the interface into
the MasterBus network. Make sure that the MasterBus network is
properly terminated at the two ends with a terminator (3).
4. A flashing LED (4) indicates that the MasterBus communication is
working.
5. Use a MasterBus compatible remote control panel such, as the
EasyView 5 or PC with MasterAdjust software, to monitor the battery.
See chapter 3 for the LIN Interface MasterBus features. For more information
refer to the user manual of the remote control panel
3 OPERATION
The LIN Interface requires no configuration. Once installed correctly, it will start operating automatically. The LIN
Interface, once powered from the LIN side, automatically starts polling the necessary data from the MLI Ultra
battery via MasterBus. It will translate this data into vehicle conform LIN messages and respond to LIN requests
received from the vehicle. In case of no active communication on the LIN Bus, the LIN Interface will go to sleep
mode (disappear from the MasterBus), until the LIN Bus communication becomes active again.
To maintain the optimal battery capacity, the battery should be charged to 100% every week.
The following table shows the LIN Interface items displayed on a monitoring device connected to the MasterBus
network.
MONITORING
DESCRIPTION
ADJUSTABLE RANGE
General
MLI Status
MLI battery status, is the battery offline or online
(read only)
MLI Data
SOC
Battery state of charge in %
(read only)
Time remaining
Time of battery use left at the actual load in hh:mm:ss
(read only)
Cap. consumed
Battery capacity consumed in Ah
(read only)
Cap. Remaining
Battery capacity remaining in Ah
(read only)
Voltage
Battery voltage in V
(read only)
Current
Current measured by the battery in A
Positive value: charging, Negative value: discharging
(read only)
Temperature
Internal temperature of the battery in °C
(read only)
Charge voltage
Current desired charge voltage in V communicated to the
vehicle
(read only)
Nom. Capacity
Nominal battery capacity in Ah
(read only)
CONFIGURATION
Device
Language
Interface menu language on a monitoring device connected to
the MasterBus network [default: English]
(read only)
Serial #
The serial number of the LIN Interface
(read only)
Name
User defined device name, visible throughout the MasterBus
network [default: LIN]
Up to 12 characters
1
4
3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mastervolt MasterBus LIN Bus Interface at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mastervolt MasterBus LIN Bus Interface in the language / languages: English as an attachment in your email.

The manual is 0.48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info