442885

Marshall VitageModern 2466, 2266, 2266C Manual

4
Zoom out
Zoom in
Previous page
1/4
Next page
Rear Panel Features (panel shown is 2466 - 2266C Combo panel is reversed)
1 2 3 4 5 6 7 8 9
54
Follow all instructions and heed all warnings
KEEP THESE INSTRUCTIONS !
ENGLISH
ENGLISH
1. Footswitch
Connecting the supplied footswitch here enables
you to perform two functions; you can change the
Dynamic Range and toggle the Reverb on and off.
The Dynamic Range switch functions exactly the
same as the front panel counterpart (11).
Effects Loop Send & Return Jacks
To increase the flexibility of your amplifier even
further, you may choose to add external effects in its
Series Effects Loop, which allows direct connection
of either floor pedals or rack processors, with the
Level switch (4) providing the correct operating
level.
2. Send
Connect the (mono) input of an external effects
processor here.
3. Return
Connect the (mono) output of an external effects
processor here.
Tonal tip: Effects involving distortion or Wah Wah
aren’t usually put in an effects loop because they
sound best when they're ‘before’ the amp (i.e.
placed between the guitar and the amp’s input).
However, when it comes to your sound, it’s up to
you!
4. Ext FX (-10dBV / +4dBu)
This switch offers two different loop levels to enable
you to match the type of effect(s) connected to the
Series Effects Loop. The higher level (+4dBu: switch
‘in’) suits rack processors and the lower level
(-10dBV: switch ‘out’) suits floor pedals (stomp
boxes).
Note: A similar level matching s
witch may also be
found on rack effect units, in which case the amp
and effects unit should be set to the same level.
5. Ext FX (Bypass/Loop)
When ‘out’ this switch completely bypasses the
circuitry involved in the effects loop. Push this switch
in to enable the loop.
Note: If this switch is accidentally pushed in and
there is nothing plugged in to the loop, the signal
will still pass through from send to return by means
of an internal link on the switching jacks. This link is
disconnected when something is plugged into the
return socket. The send socket has no effect on the
status of the internal link and could therefore be
used as a line out to a tuner for example if no
external FX are connected.
6. Speaker Outputs
WARNING! Never use the amplifier without a load
(speaker cabinet/s) attached!
There are two parallel loudspeaker output jacks
provided for connection to speaker cabinet(s).
ALWAYS ensure you use good quality speaker
(unshielded) cables. NEVER use guitar (shielded)
cables.
Always use a non-screened Marshall approved
speaker lead when connecting an extension cabinet
to these units.
7. Output Selector
This switch should be set to match your speaker
cabinet’s impedance. If more than one speaker
cabinet is connected then you should set the switch
to match the total impedance of the combination.
Check with your dealer if you are unsure.
16 & 8 ohms are provided for on the heads (2466
and 2266).
8 & 4 ohms are provided for on the combo (2266C).
Note: The impedance of the combo’s (2266C) own
speakers is 8 ohms. Make sure the combo’s output
selector is set to 8 ohms when no extension cabs
are connected.
8. HT Fuse
The correct value of this H.T. fuse is specified on
the rear panel of the amplifier. NEVER attempt to
bypass the fuse or fit one of the incorrect value!
9. Mains Input Socket with incorporated
Mains Fuse
Your amp is provided with a detachable mains
(power) lead, which is connected here. The specific
mains input voltage rating that your amplifier has
been built for is indicated on the back panel. Before
connecting for the first time, please ensure that your
amplifier is compatible with your electricity supply. If
you have any doubt, please get advice from a
qualified technician. Your Marshall dealer will help
you in this respect.
The correct value of mains fuse located in the small
drawer at the bottom of the mains socket is
specified on the rear panel of the amplifier. The
drawer contains a space for a spare fuse. NEVER
attempt to bypass the fuse or fit one of the incorrect
value!
Note: It is wise to carry spare HT and Mains fuses!
2466 Head 2266 Head 2266C Combo
Power (RMS) 100W 50W 50W
Valves 4x ECC83 + 4x KT66 4x ECC83 + 2x KT66 4x ECC83 + 2x KT66
FX Send Level - selectable
-10dBV
, +4dBu
-10dBV
, +4dBu
-10dBV
, +4dBu
Weight 22.5kg 18kg 30kg
Size (mm) W, H, D 750 x 310 x 230 750 x 310 x 230 690 x 570 x 270
Technical Specification
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marshall VitageModern 2466, 2266, 2266C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marshall VitageModern 2466, 2266, 2266C in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info