442809

Marshall Megastack (MG15FXMSDM) Manual

4
Zoom out
Zoom in
Previous page
1/7
Next page
Footcontroller (optional - PEDL-90008)
Footcontroller Factory Settings
Footswitch 1: Wish You Were Clean
Footswitch 2: Mega Rhythm
Footswitch 3: Conjuring Solo
Footswitch 4: Hangar Solo
Programming
The footcontroller can be programmed to store front
panel switches (Switch Store) or complete presets
(Preset Store).
Switch Store
To assign a front panel switch to a footswitch (1),
press and hold the front panel switch and while held
down press the footswitch (1) you wish to assign it to.
The Digital Display (3) will swirl to show that the
footswitch has been assigned. You can then release the
footswitch and front panel switch.
Preset Store
To assign a preset to a footswitch (1), select the
required channel and modify the front panel controls if
required, press and hold the Store switch on the front
panel and while held down, press your chosen
footswitch (1).
The Digital Display (3) will swirl to show that the
footswitch has been assigned. You can then release the
footswitch and Store switch.
Footcontroller Presets are independent of the dedicated
channel presets stored within the amplifier. This allows
you to create a number of presets based on the same
channel/pre-amp setting.
1
3 2
1. Footswitches
In addition to the factory preset tones, when the optional stompware® footcontroller is plugged into the
amplifier an additional four voices will be "unlocked" from the amplifier memory. These voices were programmed by
Dave Mustaine and Andy Sneap and details of the control settings and voice parameters can be found on page 41.
Each footswitch can be assigned a different stored function.
2. LED Status Panel
This always reflects the current status of the amplifier or tuner details:
CLN & OD: Current Channel
REV: Reverb On/Off
FX: FX Section On / Off
Ext FX: External FX Loop On/Off (MG50FX & MG100FX)
Damp: Damping Mode (MG50FX & MG100FX)
Tap: Tap Tempo speed.
3. Digital Display
This display indicates the various functions of the footcontroller.
ENGLISH
5
1. Footcontroller Socket
Jack socket for the connection of the optional footcontroller.
2. Loudspeaker Outputs
Connect the two loudspeaker cabinets provided to the
speaker outputs using the speaker leads supplied.
If you would like to use your MG15HFX amplifier head
with another speaker system (such as a full size 4x12"
cabinet), ensure that the amplifier is provided with a
total load equal to or greater than 8 ohms.
Always use a non-screened Marshall approved speaker
lead when connecting an extension cabinet to these
units.
MP3 / Line In
The 3.5mm MP3 / Line In socket (14) allows the
connection of an external audio source e.g. MP3 or CD
player.
Headphones
The 3.5mm Headphones socket (15) allows the
connection of a pair of headphones. When a jack is
inserted into the headphones socket the unit’s speaker
is muted.
Power
The Power switch (16) turns the amplifier on and off. If
current settings have not been stored they will be lost.
Restoring Settings - WARNING ALL AMP &
FOOTCONTROLLER SETTINGS WILL BE LOST
To restore the unit to Dave’s factory settings (see page
40) you must hold the Store switch (12) while powering
on the unit. The Clean/Crunch (3) and OD (5) lights
will light orange. You can then release the Store
switch (12).
Resetting the amplifier will erase all user Channel
presets and all user footcontroller settings, replacing
them with the factory presets.
MG15FXMSDM Features
* EUROPE ONLY - Note:
This equipment has been tested and found to comply with the requirements of the EMC Directive
(Environments E1, E2 and E3 EN 55103-1/2) and the Low Voltage Directive in the E.U.
* EUROPE ONLY - Note:
The Peak Inrush current for the MG15HFX is 2.5 amps.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
*
Reorient or relocate the receiving antenna.
*
Increase the separation between the equipment and the receiver.
*
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
*
Consult the dealer or an experienced radio/TV technician for help.
Follow all instructions and heed all warnings
KEEP THESE INSTRUCTIONS !
MG15FXMSDM Rear Panel
1 2
4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marshall Megastack (MG15FXMSDM) at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marshall Megastack (MG15FXMSDM) in the language / languages: English as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info