442720
5
Zoom out
Zoom in
Previous page
1/5
Next page
7
1. LOUDSPEAKER OUTPUTS
There are two loudspeaker output jacks provided for
connection to speaker extension cabinet(s).However,
due to the unique power amplifier output configuration,
they are not in parallel,as are standard models.Please
always ensure that the amplifier's output impedance
selector is set correctly (see item 2) and ALWAYS
ensure you use good quality speaker (non-screened)
cables.NEVER use guitar (screened) cables.
Always use a non-screened Marshall approved speaker
lead when connecting an extension cabinet to these
units.
WARNING! Never use the amplifier without a load
attached!
2. OUTPUT IMPEDANCE SELECTORS
Matches the amplifier's output to the load (speaker)
impedance.
Originally,the output selectors were situated on the
shrouds of the transformers themselves,however,this is
not allowed by current safety requirements.We have
therefore logically put them on the rear panel.
Your JTM45/100 should be completely powered down
before either Output Impedance Selector is turned.
It is imperative that:a) at least one of the speaker
outputs of the amplifier is connected to a load whilst in
operation and b) the impedances on the output
selectors matches the impedance of the extension
speaker cabinet(s) being used.The following
combinations are our recommendations:
1x16 Ohm cabinet - Selectors on 16 Ohm.
Use either speaker output.
2x16 Ohm cabinets - Both selectors on 16 Ohm.
Use both outputs.
1x8 Ohm cabinet - Selectors on 8 Ohm.
Use either output.
2x8 Ohm cabinets - Both selectors on 8 Ohm.
Use both outputs.
1x4 Ohm cabinet - Selectors on 4 Ohm.
Use either output.
2x4 Ohm cabinet - Both selectors on 4 Ohm.
Use both outputs.
Stereo cabs can be used provided attention is given to
impedance and power handling i.e.at least 50 watts per
side.
WARNING! Use of any other combination of cabinets
and/or impedances may result in sub standard sound
and possible damage to the amplifier!
Failure to comply with any of the points raised in this
section may result in damage to the amplifier.
3. MAINS INPUT
Your amp is provided with a detachable mains (power)
lead,which is connected here. The specific mains input
voltage rating that your amplifier has been built for is
indicated on the back panel.Before connecting for the
first time,please ensure that your amplifier is
compatible with your electricity supply.If you have any
doubt,please get advice from a qualified technician.Your
Marshall dealer will help you in this respect.
4. MAINS FUSE
The correct value of mains fuse is specified on the rear
panel of the amplifier.NEVER attempt to bypass the
fuse or fit one of incorrect value.
5. H.T. FUSE
The correct value of this H.T.fuse is specified on the
rear panel of the amplifier.NEVER attempt to bypass
the fuse or fit one of incorrect value.
Originally this fuse was mounted internally;however,it is
logical to provide access on the rear panel.
6
the 'low sensitivity' input was recommended for higher
output pickups (e.g.:humbuckers).This said,the majority
of guitarists - then and now - ignore these
recommendations and plug high output guitars into the
'high sensitivity' input because it further boosts the
strength of their signal.
Performance Note: ‘Jumping’ the two
channels
Because both Channels of the JTM45/100 have the
same number of gain stages and are in phase with each
other,it is possible to ‘jump’ (a.k.a.‘link’ or ‘bridge’) them
together and use them both at the same time.Doing
this enables you to expand upon the amp’s tonal
capabilities.
The most common way of doing this is to plug your
guitar into the top (high sensitivity) input of Channel I
and then run a short ‘jumper’ guitar cable (i.e.a
screened cable) from Channel I’s bottom (low
sensitivity) input to the top (high sensitivity) input of
Channel 2.Adjust both channel volumes (Loudness I & 2
controls) until the desired mix of tone is achieved.
The reverse is also possible,i.e.plugging your guitar into
Channel II’s top input and then running the ‘jumper’
cable from Channel 2’s bottom input to Channel I’s top
input.
NOTE: whether the channels are linked or not is
entirely the choice of the individual players taste in tone.
As always,experimentation is the key.
ENGLISH
ENGLISH
Follow all instructions and heed all warnings
KEEP THESE INSTRUCTIONS !
JTM45/100 Head
Power Output 100W RMS
Weight 22 kg
Size 740mm x 270mm x 210mm
812T40 & 812B40 Cabinets
Power Handling (per cabinet) 100W RMS
Weight - 812T40 36 kg
Weight - 812B40 39 kg
Size 754mm x 741mm x 355.5mm
EUROPE ONLY - Note: This equipment has been tested and found to comply with the requirements of
the EMC Dir
ective (Environments E1,E2 and E3 EN 55103-1/2) and the Low Voltage Directive in the E.U.
EUROPE ONLY - Note: The Peak Inrush current for the JTM45/100 is 39 amps.
Technical Specification
225
12 2 3 4 5
Rear panel features
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marshall JTM45_100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marshall JTM45_100 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info