38488

Marquant MCR1256 Manual

9
Zoom out
Zoom in
Previous page
1/10
Next page
6. SCAN CONTROL
Press this button to scan the receivable FM / MW stations during radio mode. When receivable stations
are tuned in, they are monitored for approximately 5 seconds before advancing to the next receivable
station. Press this button once again to stop scanning as desired.
7. PANEL RELEASE BUTTON
This button is used to release the panel from the unit.
lTo detach the front panel, press the button so that the left side of the panel is released. Grasp the
released side and pull it off of the chassis (FIGURE A).
lTo re-attach the panel, insert the right side of the panel in place first and then press the left side of the
panel until the chassis hold the panel firmly (FIGURE B).
8. MODE SELECTION / MUTE CONTROL
a) Briefly press this button to select Radio (TUNER), USB (USB-DRIV), SD (MEM-CARD) or Auxiliary Input
(AUX) mode.
b) When pressing the button for more than 2 seconds, it will mute volume control and “MUTE ON” will
appear on the display.
9.
You can enjoy RDS advantages on FM radio as following.
l Program Service Name (PS) : When an RDS station is received, station's name will appear on the display.
l Traffic Program (TP) : When station with traffic program is received, “TP” indicator will appear on the display.
l Alternative Frequencies (AF) : The unit continuously checking the signal strength of alternative frequencies
for the tuned radio station. Every time that new alternative frequency is stronger than current station, it
automatically switch over to the new frequency and new frequency will be displayed for 1-2 second. When
the button pressed short, AF switching mode is selected and the state of AF switching mode will appear on
the display as following.
-RDS indicator on : AF mode is on and RDS signal is received.
-RDS indicator off : AF mode is off.
-RDS indicator flashing : AF switching mode is selected but RDS signal is not received yet.
l Enhanced Other Networks (EON): An RDS service where the broadcaster links some stations together.
When tuned to a station which is linked to others by EON, the radio is capable of receiving Traffic
Announcement from the linked stations.
l Regional Program (for some countries only) : When tuned to a regional program, the radio will stay tuned
to that particular regional program as long as possible. If you drive out of the coverage area and the regional
program becomes very weak, the radio may tune to another regional program from the same network. To
activate the regional program function, pressing the button more than 2 seconds until “REG ON” appear on
the display. To switch off the regional program function, pressing the button more than 2 seconds until “REG
OFF” appear on the display.
RDS (RADIO DATA SYSTEM) CONTROL
10.
Press the button to select TA mode on/off. When TA mode is on, “TA” indicator will appear on the display and
the radio is able to receive traffic announcements on the same stations or stations linked via EON with Traffic
Program (TP). The TA mode can work as following.
l If the volume setting is very low, volume level will be raised temporarily during traffic announcement and
back to original volume level at the end of traffic announcement.
l Temporary switch over to an EON linked program when EON detects a traffic announcement on that other
program.
l If the radio is muted, it will be de-muted for the duration of the traffic announcement.
l If the unit is CD/MP3 mode, it will switch temporarily to radio mode to receive Traffic Announcement.
TA (TRAFFIC ANNOUNCEMENT) CONTROL
11. PTY (PROGRAMME TYPE NAME) CONTROL
There are 2 series of programme type (PTY) available for PTY search tuning. Pressing PTY button once or
twice and then pressing any Station Preset Button (1-6) until the desired PTY code appears on the display.
The radio will stop on station transmitting the selected PTY code. Next PTY searching can be activated by
repeating the same procedure. During programme type searching, PTY button can be pressed to stop
searching and the radio will back to the original station. “PTY NONE” will appear on the display if the
selected PTY code is not receivable.
12. VOLUME/SELECTION BUTTON (“VOL/SEL”)
Rotate the button anti-clockwise to decrease, or clockwise to increase volume level.
AUDIO LEVEL CONTROL (WHEN PUSHING ONE AFTER ANOTHER)
Press this button shortly one after another to show VOL/BAS/TRE/BAL/FAD control.
lVOLUME - Press this button once, then rotate anti-clockwise to decrease, or clockwise to increase
volume level.
lBASS - Press this button once, then rotate anti-clockwise to decrease, or clockwise to increase bass
level.
lTREBLE - Press this button once, then rotate anti-clockwise to decrease, or clockwise to increase
treble level.
AUDIO/SETTING SELECT (HOLD MORE THAN 2 SECONDS)
When pressing the button for more than 2 seconds, it activates as unit setting selection in cyclical mode as
following. The unit setting can be changed by rotating the button clockwise or anti-clockwise.
lTA SEEK / TA ALARM
lMASK DPI / MASK ALL
lRETUNE-S / RETUNE-L
lDSP OFF / POP M / ROCK M / CLASS M / FLAT M
lLOUD OFF / LOUD ON
lSCROLL 1 / SCROLL 2 (display showing from left to right/right to left direction)
lBEEP ON / BEEP OFF (not available for this model)
lSTEREO / MONO
lDX / LOCAL
lFADER - Press this button once, then rotate anti-clockwise or clockwise to level fader of speaker front
and rear.
lBALANCE - Press this button once, then rotate anti-clockwise or clockwise to level balance of speaker
right and left.
13/14. MANUAL UP/DOWN TUNING / TRACK SEEK UP/DOWN CONTROL
On radio mode, pressing the button for more than 2 seconds, it will tune one frequency step higher or lower.
On USB-DRIV/MEM-CARD mode, press this button will locate the beginning of the track being played or
will locate the beginning of the next track. When pressing more than 2 seconds, it will move fast forward or
fast backward to a specific position.
15. STATION PRESET BUTTON (1-6)
The PRESET BUTTONS on the unit are used to store station frequencies which you may wish to recall. Each
preset button can store FM1, FM2, FM3, MW1, MW2 band station frequency. Pressing the button momentarily
recalls the station frequency which was memorized. There are 6 preset buttons, giving you capability of storing
18FM / 12MW.
On USB-DRIV / MEM-CARD Mode
lPreset 2 - press this button to scan the first 10 seconds of all the tracks on the USB drive / SD Card.
lPreset 4 - press this button to play USB drive / SD Card at random order.
lPreset 5 - press this button to search -10 track.
lPreset 6 - press this button to search +10 track.
NOTE: When the preset button to be memorized is kept pressed for more than 2 seconds, the receiving
station frequency will be stored in the button pressed. After this, the memorized station can be recalled by
pressing the button once.
16. AUXILIARY INPUT
Press MODE button (8) until the “AUX”
mode is shown on display. The unit is
ready to play songs on an external audio
device through the auxiliary input directly
on the front panel.
17. USB HOST
The unit is ready to play MP3 songs
on an external USB device through the
USB host directly on the front panel.
18. SD CARD SLOT
Holding the SD card and insert into the slot until you hear the lock sound (Figure C).
The unit will automatically engage into MEM-CARD play mode. If you want to eject
the SD card, just press the card inward until you hear the unlock sound and then
release the card.
19. RESET BUTTON
The RESET button is located on the front of main panel. It is recessed in order to prevent accidental
engagement, and can be activated with the tip of a ball-point pen or any similar pointed object. This reset
circuitry is provided in order to protect the unit's microprocessor, and should only be activated under the
following conditions :
a) Initial installation after all wiring is completed.
b) Abnormal operation is encountered such as numerical indication on display is erratic.
c) Whenever the reset button is activated, all preset memory content will be erased and must be
reprogrammed.
FIGURE C
MP3
INPUT
AUX SD
*AUXILIARY INPUT*
Compatible with
MP3
INPUT
AUX SD
GB-3
GB-4
… 9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marquant MCR1256 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marquant MCR1256 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info