494338
2
Zoom out
Zoom in
Previous page
1/4
Next page
7
Technische gegevens
Marmitek X-10 huisautomatisering
Nominale spanning 230 Vac, 50 Hz
Opgenomen stroom < 1 W
Signaal transmissie > 5 Vpp in 5 Ω bij 120 kHz volgens
EN 50065-1, EN 50065-2-1, EN 50065-4-1
Transmissie synchronisatie 1 puls burst op 0°/180°
Signaal gevoeligheid 25 mVpp…6 Vpp bij 120 kHz ± 4 kHz
Signaal/ruis verhouding 1,35 : 1
Aansluitbereik Tot 2,5 mm
2
, aandraaimoment 0,5 Nm
Minimale omgevingstemperatuur 0 °C
Maximale omgevingstemperatuur 40 °C (*)
Atmosferische druk 86 pkA - 106 pkA
Relatieve luchtvochtigheid
(non condensing) 30 tot 90%
Normen
NEN-EN-IEC 60669-2-1, NEN-EN-IEC 60669-2-2
Markering
(*) Marmitek X-10 modules zijn geschikt voor toepassing in woningen waar de omgevings-
temperatuur in de (woon)ruimte onder normale omstandigheden niet hoger is dan 35 °C en
bij uitzondering(tijdelijk) maximaal 40 °C mag bereiken.
Technische wijzingen voorbehouden.
Elektronische apparaten en systemen kunnen gevoelig zijn voor
signalen van andere apparaten, die elektromagnetische storing
veroorzaken. Binnen de Europese Unie zijn afspraken gemaakt over
de immuniteit (gevoeligheid) van de apparatuur voor signalen en
ook de emissie (storing) van deze apparatuur. Als de apparaten/
toepassingen in een omgeving voldoen aan de daarvoor geldende
normen, zullen ze elkaar niet storen (ze zijn dan "Elektro Magnetisch
Compatibel").
Voor residentiële omgevingen, waar het huisautomatiserings -
systeem Marmitek X-10 wordt toegepast, is de Europese norm
voor immuniteit vastgelegd in de EN 61000-6-1. Apparatuur die
voldoet aan deze norm is bestand tegen de elektromagnetische
emissie van overige apparaten die voldoen aan de Europese norm
EN 61000-6-3 (residentiële omgevingen). Ervaring heeft geleerd dat
in woonhuizen apparatuur kan voorkomen dat een EMC-emissie -
niveau heeft boven de in EN 61000-6-3 vastgestelde niveaus. Deze
apparatuur kan de correcte werking van de Marmitek X-10 modules
verstoren. De immuniteit van de Marmitek X-10 inbouwmodules is
om die reden opgewaardeerd en gelijkwaardig geworden aan de
EN 61000-6-2, de strengere Europese norm voor immuniteit in
industriële omgevingen.
Desalniettemin dient het toepassinggebied van Marmitek X-
10 beperkt te blijven tot residentiële omgevingen.
Ongestoorde werking van het Marmitek X-10 systeem
8
Marmitek is niet verantwoordelijk voor het disfunctioneren
van het Marmitek X-10 systeem als gevolg van in het gebouw
aanwezige apparatuur met emissiewaardes boven de
maximale toegestane niveaus zoals die gelden in residentiële,
commerciële en lichtindustriële omgevingen en zijn
vastgelegd in de EN 61000-6-3.
Toepassing Geldende Europese norm Marmitek X-10 huis
automatisering*
Immuniteit van Emissie van Immuniteit- en
de apparatuur de apparatuur emissienorm
Residentieel 61000-6-1 61000-6-3 Compatibel/
Commercieel voldoet
Licht-industrieel
* Voorwaarde daarbij is dat het gehele Marmitek X-10 systeem wordt
geïnstalleerd volgens de geldende instructies door een gecertificeerde
en getrainde Marmitek X-10 dealer.
9
Copyrights
Marmitek is a trademark of Pattitude B.V., SVX10™ is a trademark of
Marmitek B.V. All rights reserved. Copyright and all other proprietary
rights in the content (including but not limited to model numbers,
software, audio, video, text and photographs) rests with Marmitek B.V.
Any use of the Content, but without limitation, distribution, reproduction,
modification, display or transmission without the prior written consent of
Marmitek is strictly prohibited. All copyright and other proprietary notices
shall be retained on all reproductions.
20312 - 20100927
Marmitek X-10
Signal repeater
type SVX10
PROG.
N
L
SVX
10
Marmitek X-10 Signal repeater type SVX10
Built-in module for the single phase amplification of
Marmitek X-10 signals
Technical data
Supply voltage 230 V, 50 Hz
Functions
Can be used in single or three phase installations with low
Marmitek X-10 signal levels due to cable lengths or where
appliance filters are not satisfactory.
Repeats Marmitek X-10 signals to their maximum value.
The SVX10 repeats all letter codes as standard.
Can be set up to repeat a single letter code or several
letter codes.
Can be used together with a phase coupler.
Operation
The LED is on all the time when in operating mode. The LED
flashes when Marmitek X-10 signals are received and repeated.
The SVX10 only works if the original received signal level is at
least 50 mV.
12
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek SVX10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek SVX10 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info