494278

Marmitek SafeGuard SC9000 Manual

36
Zoom out
Zoom in
Previous page
1/40
Next page
13. Frequently asked questions
Why does the security system not work?
Check whether you see any text on the console display. If not: check whether the AC adapter is connected to the mains, whether
the electrical wire is plugged into the adapter and whether the plug is connected to the console.
Check whether you can control the system via the console. If so, check whether the remote control works by checking whether
the control indicator on the remote control flashes when you press e.g. the ARM button.
Change the batteries if necessary and reinstall the remote control.
What to do if a zone indicator flashes slowly?
One of the sensors or motion detectors has not contacted the base console for a longer time. Check the batteries in the sensor or
motion detector. Erase the zone and reregister the sensor. Move the sensor so that the signal can reach the console.
If an error is found while setting the alarm, you will hear a repeated two-tone ‘error signal’. If a sensor indicates there is a
problem (e.g. window opened), you can choose not to activate this sensor.
While the two-tone ‘error signal’ can be heard, you need to press the CLEAR button and reset the alarm. The zone indicator of
the sensor concerned flashes quickly.
What to do if a zone indicator flashes quickly?
You have pressed the CLEAR button to activate the security system while a sensor or motion detector indicated an error. Solve the
problem (i.e. close the window, replace the batteries) before activating the zone.
What to do if you hear a repetitive one-tone signal when activating the alarm?
This is normal. When activating the alarm there is an exit delay of one minute to leave your house. You can alter this delay (see
8.1). After one minute the tone will stop and the system will be switched on.
What if you cannot switch the light on or off using the Lights ON or Lights OFF button on the remote control?
Make sure the HouseCode on the console is set to A and the UnitCode to 1 (see 10.6). Set the dials on your lamp/dimmer
module to HouseCode A and UnitCode 1.
Make sure the lamp connected to the lamp/dimmer module is on and the lamp is working. Use a different wall socket. Check
whether the indicator of the remote control flashes when you press the button. If necessary replace the battery/ies.
When using multiple phases in your house, you may need to couple these phases for Marmitek X-10 signals. See
www.marmitek.com/x10signal for more information.
What if you cannot register the SH624 Comfort Remote Control with the console?
Remove the batteries from the remote control. Keep one of the buttons pressed for a few seconds. Set the switch to SEC. Replace
the batteries. Press the PANIC button until the indicator starts flashing. Reregister the remote control with the console.
What to do in case of a false alarm?
Do not mount motion detectors in direct sunlight. Mount motion detectors in such a way they are not aimed at a heater or other
heat source.
Is the MS90 pet-friendly?
No. The MS90 is not specifically pet-friendly. These motion detectors do exist (not wireless). Your security system has an extra
input for wired sensors (see 9.3). You can also connect the sensor to the external contact of the DS90 sensor (9.4).
EXTRA OPTIONS
36 MARMITEK
20071_20070228_UG_SC9000_EN 08-03-2007 10:07 Pagina 36
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek SafeGuard SC9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek SafeGuard SC9000 in the language / languages: English as an attachment in your email.

The manual is 2,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marmitek SafeGuard SC9000

Marmitek SafeGuard SC9000 User Manual - Dutch - 44 pages

Marmitek SafeGuard SC9000 User Manual - French - 41 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info