494328

Marmitek RFIX35 Manual

10
Zoom out
Zoom in
Previous page
1/11
Next page
55
• Do not open the product: the device contains live parts. The
product should only be repaired or serviced by a qualified
repairman.
• In case of improper usage or if you have opened, altered and
repaired the product yourself, all guarantees expire. Marmitek
does not accept responsibility in the case of improper usage
of the product or when the product is used for purposes other
than specified. Marmitek does not accept responsibility for
additional damage other than covered by the legal product
responsibility.
56
The RF communication uses the 433.92 MHz
communication band. This band is a non-exclusively
available communication band. Therefore, interference
and limitations in range cannot be completely eliminated.
The range of the RF signals depends on a number of (external)
factors. Some of these factors are: transmitter power,
installation method and site, air humidity and construction of the
home. The materials used in homes hinder the transmission of
RF signals to some extent. Consequently, the maximum
communication distance in homes is less than the distance that
can be achieved in the open. The following list gives the
damping effect of several materials.
Absorption of RF signals
Wood, plaster, plasterboard approx. 10 %
Brick and stone, chipboard approx. 30 %
Reinforced concrete approx. 70 %
Metal (gauze), aluminium (foil) approx. 90 %
RF-signals
57
Technical data
Product characteristics
Mains voltage 230 Vac, 50 Hz
Max. power consumption < 2 W
Ambient temperature 0 to 40 °C
Frequency 433,92 MHz; X-10 RF (NEC)
compatible protocol
Max communication distance 100 m (open field)
Protection class Class II, Double insulated
Type of protection
IP 40 with wall or ceiling installation
IP 20 with installation on the wall
Standards IEC 60950
Housing
Dimension (H x W x D) 120 x 80 x 30 mm
Color RAL9001
Power cable
Dimension Length 1.5 m
Color White
58
Troubleshooting
Problem: The LED on the RFIX35 does not flash when I press the
remote control.
Cause: The remote control batteries are (almost) flat.
Solution: Replace the batteries.
Cause: The remote control (ABX1) is in the IR mode and not in the
RF mode.
Solution: Set the remote control to a RF transmitter.
Cause: The RFIX35 is not set to the same letter code as the remote
control.
Solution: Program in the same letter code on the remote control and the
RFIX35 or program the RFIX to letter code P.
Cause: The remote control is not programmed to the RF-secured mode
but the RFIX35 is.
Solution: Set the remote control to the RF-secured mode.
Cause: The remote control is programmed to the RF-secured mode but
the RFIX35 is not.
Solution: Set the remote control to the standard receive mode.
Cause: The RFIX35 is in the RF-secured mode and the remote control is
not linked.
Solution: Link the remote control in the RF-secured mode.
Cause: RF signals are not received.
Solution: Reduce the distance between the remote control and the RFIX35.
59
Problem: The transmission range is insufficient.
Cause: The receiver is too close to metal parts.
Solution: Ensure that the RFIX35 is placed away of metal parts. Do not
place on a metal plate.
Cause: Radio frequency signal interferes with the receiver.
Solution: Place the RFIX35 out of range of other electronic equipment.
Cause: The batteries are almost flat.
Solution: Replace the batteries.
Problem: There are spontaneously switching modules.
Cause: Commands from neighbours are received by the RFIX35.
Solution: Do not set the receiver to the same letter code as the neighbours.
Do not set the RFIX35 to letter code P but to a single letter code.
Set the RFIX35 to the RF-secured mode.
Cause: The RFIX35 is set to letter code P and is not programmed to the
RF-secured mode.
Solution: Set the RFIX35 to the RF-secured mode.
60
Troubleshooting (cont'd.)
Problem: After the remote control batteries are replaced, I cannot
operate anything.
Cause: The remote control batteries are incorrectly positioned or make
insufficient contact.
Solution: Check if the batteries are correctly positioned.
Cause: The letter code of the remote control has been reset to
letter code A.
Solution: Program the correct letter code into the remote control.
Cause: The remote control generates a new RF-security code that is not
recognised.
Solution: Delete all security codes in the RFIX35 and link the remote control
again.
Problem: When programming in the security code, the LED lights up
for 2 seconds.
The RFIX35 does not accept any more security codes.
Cause: The RFIX35 memory is full. All 8 remote controls are linked in the
RF-security mode.
Solution: Clear the RFIX35 memory and link the remote control(s) again.
… 10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek RFIX35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek RFIX35 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info