494300

Marmitek LM12 Manual

4
Zoom out
Zoom in
Previous page
1/24
Next page
4 © MARMITEK
Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its
packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product
should be disposed of separately from regular household waste streams. It is your responsibility to dispose
of this and other electric and electronic equipment via designated collection facilities appointed by the gov-
ernment or local authorities. Correct disposal and recycling will help prevent potential negative conse-
quences to the environment and human health. For more detailed information about the disposal of your old equip-
ment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
My modules will not respond to my controller.
Make sure that the House Code on all Modules and Controllers are set to the same House
Code (A .. P).
My modules will not react to my remote / sensor.
When you use a remote or sensor, you should have at least one TM13 Transceiver or
Marmitek Security Console installed in your house. These components will translate the radio
signals to the Marmitek X-10 signal on the power line. Only one Transceiver should be
installed for all remotes and sensors set to the same House Code.
Am I able to increase the range of my remotes by using more Transceivers?
Yes, you can use more than one TM13 Transceiver in your home when the range of your
remotes is not sufficient. The TM13 is using so called collision detection to prevent signals to
be disturbed when more than one TM13 is transmitting. TM13’s will wait for a quite power
line before transmitting their data. To prevent your Marmitek X-10 System to become slow or
to prevent dimming from becoming less smooth, make sure that the TM13 units are placed as
far away from each other as possible.
User manual LM12 Lamp Module
1. Set the House Code and Unit Code dial on the front of the Module to the desired codes.
2. Plug the lamp into the Module.
3. Plug the Module into a wall outlet.
You are now able to control your Module with any Marmitek X-10 Controller. It is also possible
to control the Module locally. Just switch the regular switch off and on shortly and the lamp will
come on (auto sense function).
Technical data
Supply voltage: 230V ±10% 50 Hz
Supply current : < 20 mA capacitive
Making capacity: 40W to 300W (normal light bulbs only)
Dimmer Speed: 4.4s from 100% to 0% ±0.2s
Signal sensitivity: 15 mVpp min 50 mVpp max at 120 kHz
Input impedance: > 55 Ohm (L - N) at 120 kHz
X-10 transmission: 1 puls burst on 0, 60 and 120 degrees.
X-10 key codes to respond to: All units Off, All Lights On, On, Off, Dim, Bright.
When using 3-phase installation: FD10 (three times) or CAT3000 needed
Fuse: F 3A 250V 5 x 20 mm
Ambient temperature: -10° C to + 50° C (operation) - 20° C to + 70° C (storage)
Dimensions: 52x122x33mm (without plug)
20135_20070403_UG_LM12 12-04-2007 11:46 Pagina 4
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek LM12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek LM12 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info