494303
5
Zoom out
Zoom in
Previous page
1/28
Next page
ENGLISH
5LD11
TM
same House Code. To solve this problem try to change the House Code of your system, or
have FD10 Phase Coupler/Filter installed at your incoming mains.
My modules will not respond to my controller.
Make sure that the House Code on all Modules and Controllers are set to the same House
Code (A .. P).
My modules will not react to my remote / sensor.
When you use a remote or sensor, you should have at least one TM13 Transceiver or
Marmitek Security Console installed in your house. These components will translate the radio
signals to the Marmitek X-10 signal on the power line. Only one Transceiver should be
installed for all remotes and sensors set to the same House Code.
Am I able to increase the range of my remotes by using more Transceivers?
Yes, you can use more than one TM13 Transceiver in your home when the range of your
remotes is not sufficient. The TM13 is using so called collision detection to prevent signals to
be disturbed when more than one TM13 is transmitting. TM13’s will wait for a quite power
line before transmitting their data. To prevent your Marmitek X-10 System to become slow or
to prevent dimming from becoming less smooth, make sure that the TM13 units are placed as
far away from each other as possible.
USER INSTRUCTIONS LD11 DIN RAIL DIMMER
SWITCH OFF APPROPRIATE MAINS FUSE AND MASTER SWITCH!
(INSTALLATION BY A CERTIFIED INSTALLER)
1. Mount the LD11 using the schematics below.
2. Set the rotary code switches on the front side to the
desired address.
When mounting more LD11 dimmers next to each other,
depending on the load per LD11, keep an extra distance of 2
cm between each LD11 to ensure the heat dissipation.
With the help of additional momentary switches on input 2,
the module can be switched on or off by a short key press and
can be dimmed by a long key press.
Technical data
Supply voltage: 230V +10% -15% 50 Hz
Supply current : < 20 mA capacitive
Making capacity: 40W/230V to 700W/230V for incandescent lamps and low voltage
halogen lights with transformer.
Soft start and soft dim. Memory function for last dimmer setting.
Control time: 3.5 sec. ± 0.2 sec. from completely on (100%) to off (0%)
Fuse: 3,15 A (T)
Signal sensitivity: 15 mVpp min 50 mVpp max at 120 kHz
Input impedance: > 60 Ohm (L - N) at 120 kHz
Connection: Connecting clamps for phase, neutral, switched phase and
pressure pulse switch
Ambient temperature: - 10° C to + 50° C (operation) - 20° C to + 70° C (storage)
Dimensions: 50x80x70mm
20141_20101018_UG_LD11_AD10 19-10-10 09:57 Pagina 5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek LD11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek LD11 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info