494333
1
Zoom out
Zoom in
Previous page
1/2
Next page
4 53 62
De dimactor is geschikt om te worden gebruikt met de meeste
electronische transformatoren geschikt voor fase-aansnijdings -
dimmers (o.a. Osram). Omdat niet elke elektronische trafo op
deze wijze gedimd kan worden is het aan te bevelen om
alvorens tot installatie over te gaan, de combinatie te testen. De
dimactor is niet geschikt voor het dimmen en schakelen van
spaarlampen en TL verlichting.
Let op!
Indien de dimactor wordt gebruikt in combinatie
met een conventionele transformator voor
halogeenverlichting, dient rekening te worden
gehouden met het volgende:
Wanneer meer dan 300 W aan gewikkelde transformatoren is
aangesloten op de dimactor, kan het gebeuren dat de bijge leverde
miniatuursmeltpatroon van 3,15 A (traag) doorsmelt. Dit treedt
bijvoorbeeld op indien de dimactor inschakelt door middel van het
All Lights On commando. De dimactor schakelt de verlichting dan
namelijk in korte tijd naar 100% hetgeen een grote inrushstroom
tot gevolg heeft. Om dit te verhelpen, levert een aantal firma’s
speciale miniatuursmeltpatronen met een hoge I
2
t- smeltwaarde:
Firma Littelfuse (type 0213) www.littelfuse.com
Firma Eska (type TT) www.eska-fuses.de
Firma Elu (type 190000) www.elu-dortmund.de
!
Marmitek X-10 Dimactor, 700 W, modulair type DAX4
Technische gegevens
Voedingsspanning: 230 V, 50 Hz
Opgenomen stroom < 0,5 W
Schakelvermogen 40 tot 700 watt
Miniatuursmeltpatroon 3,15 A (T)
Connectoren schroefconnectoren voor fase, nul en ge -
schakelde fase (sturing op aansluitpunt 2)
Toepassingsmogelijkheden
Dimmer voor montage op hoedprofiel.
Schakelt en dimt verlichtings-circuits tot 700 W.
Geschikt voor verlichting op 230 V en voor
laagspanningsverlichting met trafo, inclusief
halogeenverlichting.
Kan op afstand aangestuurd worden met Marmitek X-10
commando’s van de dimmerinterfaces DIX1 en DIX2 of van een
afstands bediening of computerinterface. Tevens kan de
dimactor recht streeks bediend worden door één of meerdere
impulsdrukkers.
Voorzien van soft start en soft dim en geheugen voor de
laatste dim stand.
Kan vanuit 0% naar het gewenste dim-niveau worden
geregeld.
Reageert op Marmitek X-10 commando’s ‘’Aan’’, ‘’Uit’’, ‘’Dimmen’’,
‘’Feller’’, ‘’All Lights On’’,‘’All Lights Off’’ en ‘’All Units Off’
De miniatuursmeltpatronen van de firma Littelfuse zijn onder
andere verkrijgbaar bij:
Futureelectronics.com en Arrow.com
Installatie
Eerst de spanning uitschakelen voordat u met de
montage begint.
!
Aansluitschema
Lamp of apparaat Impulsdrukker
L
L
N
2
L
N
The dimming actuator is suitable for use with most electronic
transformers suitable for phase control dimmers (including
Osram). As not all electronic transformers can be dimmed this
way, it is advisable to test the combination before installing. The
dimming actuator cannot be used to dim/switch energy-saving
lamps and fluorescent lamps.
Note
If the dimming actuator is used for halogen lighting
with a conventional transformer, the following
should be taken into account:
If more than 300 W in wound transformers is connected to the
dimming actuator, the 3.15 A (slow) miniature cartridge fuse
supplied may blow. This will happen, for example, if the
dimming actuator is switched on by the All Lights On command.
In this case, the dimming actuator switches the lighting to
100% very quickly, producing a high inrush current.
To remedy this situation a number of companies supply a
special miniature cartridge fuse with a high I
2
t fuse value:
Littelfuse (type 0213)
www.littelfuse.com
Eska (type TT) www.eska-fuses.de
Elu (type 190000) www.elu-dortmund.de
!
Marmitek X-10 Dimming actuator, 700 W, modular type DAX4
Technical data
Supply voltage 230 V, 50Hz
Current consumption < 0,5 W
Switch capacity 40 tot 700 watt
Miniature cartridge fuse 3.15 A (T)
Connectors Screw connectors for phase, neutral and
switched phase (control on connection
point 2)
Application options
Dimmer for mounting on top-hat rail.
Switches and dims lighting circuits up to 700 W.
Suitable for 230 V lighting and low voltage lighting with
transformers, including halogen lighting.
Suitable for remote control with Marmitek X-10 commands
from the DIX1 and DIX2 dimmer interfaces, or a remote
control unit or computer interface. The dimming actuator can
also be directly controlled by one or more toggle pulse
switches.
Equipped with soft start and soft dim and memory for the last
dimming position.
Can be controlled from 0% to the desired dimming position.
Reacts to Marmitek X-10 commands ''On'', ''Off'', ''Dim'',
''Brighter'', ''All Lights On'',''All Lights Off'' and ''All Units
Off''
The miniature cartridge fuses manufactured by Littelfuse are
available from:
Futureelectronics.com and Arrow.com
Installation
Always switch off the power supply before
commencing installation.
!
Wiring diagram
Lamp or transformer Toggle pulse switches
L
L
N
2
L
N
Instellen van het Marmitek X-10 adres
Door het verdraaien van draaischakelaars aan de voorzijde van
de dimactor, kunt u de gewenste lettercode (A t/m P) en
cijfercode (1 t/m 16) instellen.
Bij montage van meerdere dimactoren op een hoedprofiel,
dient, afhankelijk van de belasting, rekening gehouden te
worden met 2 cm afstand tussen de
dimactoren om voldoende warmte dissipatie te garanderen.
Let op!
Behalve comfort kan automatisch schakelen ook
gevaar met zich meebrengen. Zo kunnen anderen
verrast worden, of kan kleding welke over een
elektrische warmtebron hangt in brand raken.
Wees hier altijd op bedacht en neem afdoende
maatregelen ter voorkoming.
!
Setting the Marmitek X-10 address
Turn the rotary switches at the front of the dimming actuator to
set the desired letter code (A to P) and number code (1 to 16).
When several dimming actuators are installed on a top-hat rail,
and depending on the load, a distance of 2 cm should be
maintained between the dimming actuators to allow heat to
dissipate.
Note
Automatic switching does not just increase the
level of comfort, a number of hazards are also
involved. People may be surprised, or clothing
placed over an electrical heat source may ignite.
Always be aware of these hazards and take the
necessary precautions.
!
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek DAX4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek DAX4 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info