161017
31
Zoom out
Zoom in
Previous page
1/35
Next page
27
ENGLISH
7
Sleep timer
The sleep timer function allows the unit to be in standby
mode automatically after specific period of time.
1. Press the SLEEP button m on the remote control.
2. Each press of the button will increase the time before
shut down in the following sequence.
3. The sleep timer will be shown for 5 seconds in the
display, and it will count down until the time has elapsed.
When the programed sleep timer has elapsed, the unit
will automatically turn off.
Note that the display will be dimmed when the sleep
timer is programed.
4. Press the SLEEP button m. The display shows the
remaining time until standby mode begins.
5. To cancel the sleep timer, press the SLEEP button m
repeatedly until the display shows "SLEEP OFF".
When the sleep timer is programed, DIMMER function
does not activate.
10
20
30 60 90 120OFF
OTHER OPERATION
REMOTE CONTROLLER
RC7001ST
SHIFT
R
E
E
N
T
BAND MENU
TUNING
CONTROL
CHANNEL/
A/B C/D E/F
TIMER
10
DISPLAYDIMMER
987
456
32
T-MODEI/JG/H
SLEEP MEMO
ONSTANDBY
1
/A-TUNE
A-PRESET
m
LAST FUNCTION MEMORY
This unit is equipped with a last function memory which
stores the input and output setting conditions as they were
immediately before the power is switched off.
This function eliminates the need to perform complicated
resettings when the power is turned on.
The unit is also equipped with a back-up memory.
This function provides approximately one week of memory
storage when the main units power switch is off and with
the mains cord disconnected.
INITIALIZATION OF THE
MICROPROCESSOR
When the indication of the display is not normal or when
the operation of the unit does not shows the reasonable
result, the initialization of the microprocessor is required
by the following procedure.
1. Unplug the mains cord from the power outlet after
pressing the POWER ON/STANDBY switch q and
setting the standby mode.
2. Holding both the DIMMER button r and MENU button
u, plug the mains cord into the power outlet.
3. Check that the entire display is flashing with an interval
of about 1 second, and release your fingers from the 2
buttons and the microprocessor will be initialized.
Note
If step 3 does not work,start over from step 1.
If the microprocessor has been initialized all the button
settings are reset to the default values (the values set
upon shipment from the factory).
PUSH ENTERPUSH ENTER
TUNING/PRESETTUNING/PRESET
STEREOSTEREO
RDSRDS
TUNEDTUNED
SECONDARYSECONDARY
BAND SELECTBAND SELECT
AUTO TUNEAUTO TUNE
MENUMENU
DISPLAYDISPLAY
DIMMERDIMMER
STANDBYSTANDBY
ON/STANDBYON/STANDBY
POWERPOWER
DAB/FM/AM TUNER ST7001DAB/FM/AM TUNER ST7001
q r u
ST7001N 01 Eng 05.7.21 5:24 PM ページ27
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz st7001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz st7001 in the language / languages: English as an attachment in your email.

The manual is 1,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info