6592
15
Zoom out
Zoom in
Previous page
1/54
Next page
11
ENGLISH
⁄5 CURSOR / OK button
Used to operate on-screen and other displays used by receivers and
other components.
⁄6 CH SEL. (channel select) button
(when AMP mode is selected)
Used to call up SETUP MAIN MENU and adjust speaker levels or 6.1
ch input level.
⁄7 SETUP button
(when AMP mode is selected)
Used to call up the setup menu of the SR7300.
⁄8 CONTROL buttons
These buttons are used when operating the CD player, TAPE deck,
etc.
The function of these buttons are dependent on the function button
selected.
(when AMP mode is selected)
ATT button
When the input signal is too high and the voice distorts even by throt-
tling the SR7300 VOLUME control, turn on this function. ATT is indi-
cated when this function is activated.
The input level is reduced. Attenuator is invalid for use with the output
signal of REC OUT.
Note:
This function is unavailable during the digital input is selected.
SPK A/B button
Speaker mode is switched in the following sequence.
A B A+B off
MULTI button
This button is used to switch the unit to multi room mode.
⁄9 Input selector buttons/ FUNCTION SE-
LECTOR buttons (AUDIO/VIDEO INPUT)
Used to switch the remote controller to the command sets for specific
sources (amplifier, receiver, etc.), thereby allowing a single remote
controller to control up to 11 different components. To use these
buttons to switch the amplifiers source, press the desired button twice
within 2 seconds. The AMP button ⁄9 is used only to switch command
set of the remote controller itself and therefore does not transmit any
signal. Further, the function buttons may also be programmed to
execute macros. (A macro allows a complex string of operations to be
performed in series simply by pressing a single button.) One button
can be programmed to learn sequences containing up to 10
commands. The following is an example of such a sequence that can
be activated automatically using a macro:
Turn the receiver ON Switch the function to DVD Set the
Surround Mode to VIRTUAL Set the DVD player to Play.
¤0 EXIT button
(when AMP mode is selected)
Used to exit SETUP MAIN MENU.
¤1 TEST button
(when AMP mode is selected)
Used to enter the test tone menu.
¤2 MENU/OSD button
(when AMP mode is selected)
When this button is pressed, the current setting are displayed on the
TV monitor.
¤3 VOLUME / buttons
Used to adjust the volume on receivers and other components (TV)
equipped with volume control.
¤4 P.SCAN (preset scan) button
(when TUNER mode is selected)
Used to start preset scan when SR7300 is selected TUNER mode.
¤5 MUTE button
Muting button of the SR7300. Press this button decrease the sound
temporarily . Press this button again to return to the previous sound.
¤6 MEMO button
Memory enable button for various preset functions.
¤7 NIGHT button
(when AMP mode is selected)
Pressing this button prevents the Dolby Digital signal from playback at
a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum.
Thus, it eliminates the occurrence of an abruptly loud voice at night.
However, the function is valid only for the case when the Dolby Digital
signal is entered into OPTICAL or COAXIAL and data to compress the
voice exists in the signal to be played back.
When this button is pressed, NIGHT indicator lights up.
¤8 PTY button (European model only)
(when TUNER mode is selected)
Used to display the programme type information of the current station.
The RDS system categorizes programmes according to their genre
into different programme type (PTY) groups.
¤9 F.DIR/SEAR button
(when TUNER mode is selected)
Used to select the mode of frequency direct input.
‹0 DISP./RDS button (European model only)
(when TUNER mode is selected)
Selects display mode function in RDS (Radio Data System) by this
button.
(when AMP mode is selected)
( When this button is pressed once, the display is dimmed.
When this button is pressed twice, the display is turned off and
DISPLAY OFF indicator lights up.
Press this button again to turn the display ON again.)
‹1 A/D button
This is used to switch between the analog and digital inputs.
‹2 SLEEP (sleep timer) button
This button is used for setting the sleep timer. It can be operated the
same way as the button in unit.
‹3 7.1/6.1CH IN button
Press this button to select the output of an external multi channel decoder.
‹4 POWER ON, OFF buttons
(when AMP mode is selected)
Press to switch the power of the SR7300 ON or OFF.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-7300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-7300 in the language / languages: English as an attachment in your email.

The manual is 4,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info