Manual Marantz CR401 (page 25 of 29) (English)

37777

Zoom out

Zoom in

1/29

ENGLISH

Confirm and change timer

program

• You can check and change the timer program

setting as follows.

1. Press the TIMER button x.

2. Either turn the Easy JOG 4/¢ knob !5 or

press the 5 or ∞ button c to select timer

program number.

3. You can change the displayed contents with the

Easy JOG 4/¢ knob !5 or 5 or ∞ button

c and ENTER buttons b if necessary.

Note

• Timer program is not changed if you quit

confirming halfway through a procedure.

Timer program off

1. Press the TIMER button x, “TIMER

PROGRAM 1” is displayed.

2. Either turn the Easy JOG 4/¢ knob !5 or

press the 5 or ∞ button c to select timer

program number.

3. Press the Easy JOG 4 /¢ knob !5 or

ENTER button b, “TIMER PROGRAM x SET”

is displayed.

4. Either turn the Easy JOG 4/¢ knob !5 or

press the 5 or ∞ button c to select “TIMER

PROGRAM x OFF”.

5. Press the Easy JOG 4 /¢ knob !5 or

ENTER button b to turn off the timer program.

Note

• To turn a timer program back on again, repeat

this procedure and select “TIMER PROGRAM x

ON”.

Sleep timer

• The sleep timer function allows the unit to be in

standby mode automatically after specific period

of time.

1. Press the SLEEP button ⁄7 on the remote

control.

2. Each press of the button will increase the time

before shut down in the following sequence.

3. The sleep timer will be shown for 5 seconds in

the display, and it will count down until the time

has elapsed. When the programed sleep timer

has elapsed, the unit will automatically turn off.

Note that the display will be dimmed when the

sleep timer is programed.

4. Press the SLEEP button ⁄7. The display shows

the remaining time until standby mode begins.

5. To cancel the sleep timer, press the SLEEP

button ⁄7 repeatedly until the display shows

“SLEEP OFF”.

• When the sleep timer is programed, DIMMER

function does not activate.

30 60 90 120OFF

LAST FUNCTION MEMORY

• This unit is equipped with a last function memory

which stores the input and output setting

conditions as they were immediately before the

power is switched off.

This function eliminates the need to perform

complicated resettings when the power is turned

on.

• The unit is also equipped with a back-up

memory.

This function provides approximately one week

of memory storage when the main unit’s power

switch is off and with the mains cord

disconnected.

INITIALIZATION OF THE

MICROPROCESSOR

• When the indication of the display is not normal

or when the operation of the unit does not shows

the reasonable result, the initialization of the

microprocessor is required by the following

procedure.

1. Unplug the mains cord from the power outlet

after pressing the POWER ON/STANDBY

switch q or button z and setting the

standby mode.

2. Holding both the MENU button u and POWER

ON/STANDBY switch q, plug the mains cord

into the power outlet.

3. Check that the entire display is flashing with an

interval of about 1 second, and release your

fingers from the 2 buttons and the

microprocessor will be initialized.

Notes

• If step 3 does not work,start over from step 1.

• If the microprocessor has been initialized all the

button settings are reset to the default values

(the values set upon shipment from the factory).

STANDBYSTANDBY

PHONESPHONES

POWER ON / STANDBYPOWER ON / STANDBY

CD RECEIVER CR401CD RECEIVER CR401

PUSH TO ENTERPUSH TO ENTER VOLUMEVOLUME

TREBLETREBLEBASSBASS

INPUTINPUT MENUMENU DIRECTDIRECT

!5 u

MEMO

AUTO TUNE SLEEP SHIFT

DIRECT

AMFMDAB

--/---

MUTE

DISPLAY

VOL

INPUT

DIMM

VOL

10/0

INPUT

MODE

TUNING

PRESET

ENTER

CLOCK

CALL

CLEAR

TIMER

REPEAT

REMOTE CONTROLLER

RC601CR

REMOTE CONTROLLER

RC601CR

REMOTE CONTROLLER

RC601CR

⁄7

OTHER OPERATION

CR401N_01 Eng 05.11.18 4:55 PM ページ21

can a turntable be connected to this unit? there is no phono input as such nor a ground connection so I'm thinking not; I tried a few of the options with no success Submitted on 27-12-2019 at 12:51
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Marantz CR401 in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Marantz CR401 Manual

Product: