589963
14
Zoom out
Zoom in
Previous page
1/15
Next page
14
4. When finished the slave receiver will reboot and come up with a channel.
TROUBLE SHOOTING GUIDE
If you suspect there is a problem with your receiver, please check the following trouble shooting guide before
calling a Manhattan authorised service agent.
WARNING! Do NOT attempt to repair the receiver yourself. Tampering with the receiver may
result in fatal electric shock and will invalidate your warranty.
Symptoms --- Possible cause / solutions
Front display not lit --- Check that the mains lead is plugged into the power socket. Check that your TV is
tuned for the correct UHF channel or is switched to correct AV input.
No picture or sound or any menus --- No signal. Channel is scrambled. The antenna is not in correct
position. Check LNB wire is not damaged or shorting. Check LNB may be faulty. Unplug receiver from power
socket and retry.
Interference, on picture, using UHF output --- Local terrestrial TV interference. Change the UHF output
channel to different one then re-tune your TV. Select the appropriate ‘TV Standard’ using TV Settings menu.
Bad picture with blocking or frozen --- Signal weak or noisy. Check signal quality. Antenna not in correct
position
Not responding to remote control --- Check the batteries in your remote control. Replace with new.
You have lost or forgotten your password --- Apply master password or contact your Manhattan dealer.
SPECIFICATIONS
TUNER
Input Connector F-type IEC 169-24 Female
Frequency Range 950MHz to 2150MHz
Input Impedance 75 Ohm
Signal Level -25 to - 65 dBm
LNB Power & Polarization Vertical +14V, Horizontal +18V (600mA Max. with Overload
Protection)
LNB Control 22KHz 4 KHz, Tone burst A/B and DiSEqC 1.2
22 KHz Tone Amplitude 0.6Vpp (…0.2V)
Input Symbol Rate 2~45 Msps
FEC Decoder Auto, 1/2, 2/3, 3/4, 5/6, 7/8
SYSTEM
Transmission Standard DVB MPEG-2
Input Data Rate Max 15Mb/s
Aspect Ratio 4:3, 16:9
Video Resolution 720 x 480 NTSC, 720 x 576 PAL
Audio Decoding MPEG Layer 1 & 2
Audio Mode Single channel / Dual Channel/Joint Stereo / Mono
Sampling Rate 32KHz, 44.1 KHz, 48 KHz, 96 KHz,
COMMON INTERFACE (optional)
Slots 2 slots type 1 and type 2
PCMCIA DVB Common Interface Standard
IRDETO EMBEDDED CI (optional)
Card Slot 1 Slot
PCMCIA DVB Common Interface Standard
CONNECTORS
RGB, CVBS 2 SCART sockets (TV/VCR), 1 PHONO RCA
Audio Output 2 SCART sockets (TV/VCR), 2 x PHONO (L, R) / RCA
Digital Audio Output 1 PHONO RCA (S/P DIF)
Data Interface 1 RS232 (Bit Rate: 115,200 baud Connector: 9-pin D-sub type)
RF connectors 75 Ohm IEC 169-2 Male/Female
SPECIFICATIONS
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Manhattan PLAZA ST 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Manhattan PLAZA ST 200 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info