Manual Makita UN490D (page 9 of 30) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

600703

Zoom out

Zoom in

1/30

010823

Battery remaining capacity indicator (only

for models with Battery BL3622A)

Battery BL3622A is equipped with the battery remaining

capacity indicator. (Fig. 4)

Press the CHECK button to indicate the battery remaining

capacity. The indicator lamps will then light for approx.

three seconds.

011713

• When only the lowermost indicator lamp (next to the

“E”) blinks, or when none of the indicator lamps light,

the battery capacity has run out, so the tool does not

operate. In these cases, charge the battery or replace

the empty battery with a fully charged one.

• When two or more indicator lamps do not light even

after charging is complete, the battery has reached the

end of its service life.

• When the upper two and lower two indicator lamps light

alternately, the battery may have malfunctioned.

Contact your local Makita authorized service center.

NOTE:

• The indicated capacity may be lower than the actual

level during use or immediately after using the tool.

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

Power switch action

WARNING:

• Before inserting the battery cartridge in the tool,

always check to see that the switch trigger

actuates properly and returns to the “OFF”

position when released. Do not pull the switch

trigger hard without pressing in the lock-off button.

This can cause switch breakage. Operating a tool

with a switch that does not actuate properly can lead to

loss of control and serious personal injury. (Fig. 5)

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, press in the lock-off button and pull the

switch trigger. The tool speed is increased by increasing

pressure on the switch trigger. Release the switch trigger

to stop.

Reversing switch for debris removal

(Fig. 6)

This tool has a reversing switch. To remove a branch

caught in the blades, depress the “B” side of the switch to

reverse the rotation. For normal operation, depress the

“A” side of the switch.

In the reverse position the tool operates only for a short

period of time and automatically shuts off.

NOTICE:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage it.

Speed change (Fig. 7)

Two speed ranges can be preselected with the speed

change switch.

Flipping the speed change switch lever to the “1” position

will set the tool to the low speed range and the “2” position

will set the tool to the high speed range.

Status Action to be taken

-Blinking

Battery power has been nearly used

up.

Replace the battery with fully charged

one.

- Lighting On

Battery protector is shutting off the

power - battery power has been used

up.

Replace the battery with fully charged

one.

Blinking -

Overload protector is shutting off the

power - the motor was locked.

Release the switch trigger and remove

the cause of the motor lock or

overload. If the cutting tool is locked by

entangling weeds or the like, always

remove the battery cartridge before

clearing it.

Lighting On -

Overheat protector is shutting off the

power - overheating.

Rest the equipment for a while.

Blinking Blinking Electric or electronic malfunction

Ask your local authorized service

center for repairs.

Indicator lamps

Remaining capacity

Lighted Off Blinking

E F

70% to 100%

45% to 70%

20% to 45%

0% to 20%

Charge the battery.

The battery may have

malfunctioned.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita UN490D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita UN490D Manual

Product: