Manual Makita M9001 (page 4 of 22) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691557

Zoom out

Zoom in

1/22

ENGLISH (Original instructions)

Explanation of general view

1 Shaft lock

2 Switch trigger

3 Lock lever

4 Wheel guard

5Screw

6 Bearing box

7 Lock nut

8 Depressed center grinding

wheel

9 Inner flange

10 Lock nut wrench

11 Abrasive cut-off wheel/diamond

wheel

12 Wheel guard for abrasive cut-off

wheel/diamond wheel

13 Outer flange 78

14 Inner flange 78

15 Exhaust vent

16 Inhalation vent

17 Commutator

18 Insulating tip

19 Carbon brush

20 Brush holder cap

21 Screwdriver

SPECIFICATIONS

• Due to our continuing program of research and

development, the specifications herein are subject to

change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE091-1

Intended use

The tool is intended for grinding and cutting of metal and

stone materials without the use of water.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

ENF100-1

For public low-voltage distribution systems of

between 220 V and 250 V.

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under

unfavorable mains conditions can have adverse effects

to the operation of other equipment. With a mains

impedance equal or less than 0.24 Ohms it can be

presumed that there will be no negative effects. The

mains socket used for this device must be protected with

a fuse or protective circuit breaker having slow tripping

characteristics.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future refer-

ence.

GEB129-1

GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding or Abrasive

Cutting-Off Operations:

1. This power tool is intended to function as a

grinder or cut-off tool. Read all safety warnings,

instructions, illustrations and specifications

provided with this power tool. Failure to follow all

instructions listed below may result in electric shock,

fire and/or serious injury.

2. Operations such as sanding, wire brushing or

polishing are not recommended to be performed

with this power tool. Operations for which the

power tool was not designed may create a hazard

and cause personal injury.

3. Do not use accessories which are not

specifically designed and recommended by the

tool manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

6. Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by flanges, the arbour hole of the

accessory must fit the locating diameter of the

flange. Accessories that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

Model M9000 M9001

Depressed center wheel diameter 180 mm 230 mm

Max. wheel thickness 6.0 mm 6.0 mm

Spindle thread M14 or 5/8" (country specific)

Rated speed (n) / No load speed (n

) 8,500 min

–1

6,600 min

–1

Overall length 466 mm 466 mm

Net weight 5.4 kg 5.7 kg

Safety class /II /II

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita M9001 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 0,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita M9001 Manual

Product: