448471
5
Zoom out
Zoom in
Previous page
1/7
Next page
Switch action
CAUTION:
Before plugging in the machine, always check to
see that the switch trigger actuates properly and
returns to the ‘‘OFF’’ position when released.
Do not tape, tie or otherwise secure the trigger in
the ‘ON’’ position.
For HK1800 (Fig. 3)
To start the machine, simply pull the trigger. Release
the trigger to stop.
For HK1810 (Fig. 4)
To start the machine, simply pull the trigger. Machine
speed is increased by increasing pressure on the
trigger. Release the trigger to stop. A speed control
screw is provided so that maximum machine speed
can be limited (variable). Turn the speed control
screw clockwise for higher speed, and counterclock-
wise for lower speed.
Operation (Fig. 5)
Position the chisel at the location to be scaled, then
pull the trigger. Apply light pressure to the machine.
Forcing the machine will only decrease the machine
performance.
MAINTENANCE
CAUTION:
Always be sure that the machine is switched off and
unplugged before carrying out any work on the
machine.
Replacement of carbon brushes (Fig.6&7)
Whenever carbon brushes must be replaced, they cut
out the machine automatically. When this occurs,
remove the rear cover and then replace both carbon
brushes at the same time. Use only identical carbon
brushes.
Lubrication (Fig.8&9)
This machine requires no hourly or daily lubrication
because it has a grease-packed lubrication system.
Lubricate the machine every time the carbon brushes
are replaced.
Run the machine for several minutes to warm it up.
Switch off and unplug the machine. Remove the crank
cap using a Makita lock nut wrench 28 (optional
accessory). Rest the machine on the table with the bit
end pointing upwards. This will allow the old grease to
collect inside the crank housing. Wipe out the old
grease inside and replace with a fresh grease (20 g).
Use only Makita genuine grease (optional accessory).
Filling with more than the specified amount of grease
(approx. 20 g) can cause faulty hammering action or
machine failure. Fill only with the specified amount of
grease. Reinstall the crank cap and tighten with the
lock nut wrench. Do not tighten the crank cap exces-
sively. It is made of resin and is subject to breakage.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by
Makita Authorized Service Center.
HK1800/HK1810 (E) (’98. 4. 24)
5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HK 1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HK 1800 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita HK 1800

Makita HK 1800 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info