448449
5
Zoom out
Zoom in
Previous page
1/56
Next page
5
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
Note: Specifications may differ from country to country.
Symbols
END202-2
The following show the symbols used for the tool. Be sure
that you understand their meaning before use.
................ Read instruction manual.
................ DOUBLE INSULATION
................ Wear safety glasses.
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.23 Ohms it can be presumed that
there will be no negative effects. The mains socket used
for this device must be protected with a fuse or protective
circuit breaker having slow tripping characteristics.
ADDITIONAL SAFETY RULES
ENB031-6
1. Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves,
helmet and apron should be worn.
2. Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
3. Keep guards in place.
4. Use only wheels with correct size and wheels hav-
ing a maximum operating speed at least as high as
the highest No Load Speed marked on the tool’s
nameplate. When using depressed center wheels,
be sure to use only fiberglass-reinforced wheels.
5. Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged
wheel immediately.
6. Observe the instructions of the manufacturer for
correct mounting and use of wheels. Handle and
store wheels with care.
7. Do not use separate reducing bushings or adap-
tors to adapt large hole abrasive wheels.
8. Use only flanges specified for this tool.
9. Do not damage the spindle, the flange (especially
the installing surface) or the lock nut. Damage to
these parts could result in wheel breakage.
1. Shaft lock
2. Motor housing
3. Lock button
4. Handle
5. Switch trigger
6. Lock lever
7. Wheel guard
8. Screw
9. Bearing box
10. Nut
11. Lever
12. Lock nut
13. Depressed center wheel
14. Super flange
15. Inner flange
16. Lock nut wrench
17. Outer flange 78
18. Cut-off wheel
19. Inner flange 78
20. Dust collecting wheel guard
21. Exhaust vent
22. Inhalation vent
23. Commutator
24. Insulating tip
25. Carbon brush
26. Brush holder cap
27. Screwdriver
28. Side grip
29. Bolt
30. Grip attachment
31. Lock nut
32. Diamond wheel
33. Spindle
Model
GA7030/GA7030F/
GA7030S/GA7030SF
GA7040S/GA7040SF
GA9030/GA9030F/
GA9030S/GA9030SF
GA9040S/GA9040SF
Depressed center wheel
diameter
180 mm 230 mm
Spindle thread M14 M14
No load speed (min
-1
) 8,500 6,600
Overall length 511 mm 511 mm
Net weight 5.1 kg 5.5 kg 5.1 kg 5.5 kg
Safety class /II
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita GA9040S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita GA9040S in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info