599691
5
Zoom out
Zoom in
Previous page
1/88
Next page
5
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
Symbols
END202-8
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
...... Read instruction manual.
................ DOUBLE INSULATION
...... Wear safety glasses.
.................. Only for EU countries
Do not dispose of electric equipment
together with household waste
material!
In observance of the European
Directive, on Waste Electric and
Electronic Equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.
Intended use
ENE048-1
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
ENF002-2
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For model GA7050, GA9050
ENF100-1
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects to
the operation of other equipment. With a mains
impedance equal or less than 0.22 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
1. Shaft lock
2. Switch trigger
3. Lock lever
4. Indication lamp
5. Wheel guard
6. Screw
7. Bearing box
8. Nut
9. Lever
10. Lock nut
11. Depressed center wheel
12. Inner flange
13. Super flange
14. Lock nut wrench
15. Abrasive disc
16. Rubber pad
17. Ezynut
18. Abrasive wheel/Multi-disc
19. Spindle
20. Arrow
21. Notch
22. Wire cup brush
23. Wire wheel brush
24. Abrasive cut-off wheel/diamond
wheel
25. Wheel guard for abrasive cut-off
wheel/diamond wheel
26. Outer flange 78
27. Inner flange 78
28. Exhaust vent
29. Inhalation vent
30. Commutator
31. Insulating tip
32. Carbon brush
33. Brush holder cap
34. Screwdriver
Model GA7050 GA7050R GA9050 GA9050R
Depressed center wheel
diameter
180 mm
180 mm 230 mm 230 mm
Max. wheel thickness 6.5 mm 6.5 mm 6.5 mm 6.5 mm
Spindle thread M14 or 5/8” (country specific)
No load speed (n
0
)/
Rated speed (n)
8,500 (min
-1
)
8,500 (min
-1
) 6,600(min
-1
) 6,600 (min
-1
)
Overall length 432 mm 455 mm 432 mm 455 mm
Net weight 4.5 kg 4.6 kg 4.7 kg 4.8 kg
Safety class /II
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita GA7050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita GA7050 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info