600650

Makita DA6301 Manual

4
Zoom out
Zoom in
Previous page
1/36
Next page
ENGLISH
Explanation of general view
1 Tighten
2 Chuck
3 Chuck key
4 Spade grip
5 Hex. bolt
6 Brace pipe here.
7 Reaction
8 Forward
9 Drilling in forward bit turns
clockwise
0 Reverse
q Reversing bit turns counter-
clockwise
w Counterclockwise
e Switch
r Clockwise
t Pin
y Slide button
u Limit mark
i Screwdriver
o Brush holder cap
SPECIFICATIONS
Model DA6301
Drilling capacities
Wood
Auger-bit ..................................................................................................................... High: 29 mm (1-1/8″)
Low: 38 mm (1-1/2″)
Ship-auger-bit ............................................................................................................. High: 38 mm (1-1/2″)
Low: 38 mm (1-1/2″)
Self-feed bit ................................................................................................................ High: 35 mm (1-3/8″)
Low: 118 mm (4-5/8″)
Steel .................................................................................................................................. High: 13 mm (1/2″)
Low: 13 mm (1/2″)
No load speed (min
–1
) ..................................................................................................................... High: 1,200
Low: 300
Overall length .............................................................................................................................. 330 mm (13″)
Overall length (Extended spade grip) .................................................................................. 410 mm (16-3/16″)
Net weight ................................................................................................................................... 4.3 kg (9.5 lbs)
•
Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
•
Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
ADDITIONAL SAFETY RULES
1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting
tools may contact hidden wiring or its own
cord. Contact with a ‘‘live’’ wire will make
exposed metal parts of the tool ‘‘live’’ and
shock the operator.
2. Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the tool
only when hand-held.
6. Do not touch the drill bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
7. PROPER GROUNDING. This tool should be
grounded while in use to protect the operator
from electric shock.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing drill bit (Fig. 1)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
To install the bit, place it in the chuck as far as it will
go. Tighten the chuck by hand. Place the chuck key in
each of the three holes and tighten clockwise. It is
important to tighten the chuck with all three holes
evenly. To remove the bit, turn the chuck key coun-
terclockwise in just one hole, then loosen the chuck
by hand.
Spade grip (Fig. 2 & 3)
The spade grip can be installed in either of the
positions as shown in the figure. When changing the
location of the spade grip from one position to the
other, loosen the hex bolts with a wrench and turn the
spade grip to another position. Then tighten the hex
bolts securely.
4
DA6301 (E) (’100. 1. 13)
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DA6301 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DA6301 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info