389379
5
Zoom out
Zoom in
Previous page
1/9
Next page
5
ENGLISH
Explanation of general view
1 Abrasive disc
2 Dust bag
3 Dust nozzle
4 Push button
5Hook
6Groove
7 Front fixing cardboard
8 Front side of paper dust bag
9 Claws
10 Upper part
11 Notch
12 Guide
13 Screwdriver
14 Front grip
15 Hole in front grip
16 Notches
17 Speed adjusting dial
18 Lock button
19 Switch trigger
20 Sponge pad
21 Felt pad
22 Wool pad
SPECIFICATIONS
Model BO5020 BO5021
Pad diameter ........................................................................ 123 mm 123 mm
Abrasive disc diameter ......................................................... 125 mm 125 mm
Orbits per minute ................................................................. 12,000 4,000 12,000
Overall length ....................................................................... 288 mm 288 mm
Net weight ............................................................................ 1.4 kg 1.4 kg
Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
Note: Specifications may differ from country to
country.
Intended use
The tool is intended for the sanding of large surface
of wood, plastics and metal materials as well as
painted surfaces.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
Safety instructions.
ADDITIONAL SAFETY RULES
ENB042-4
1. Hold the tool firmly.
2. Do not leave the tool running. Operate the
tool only when hand-held.
3. This tool has not been waterproofed, so do
not use water on the workpiece surface.
4. Ventilate your work area adequately when
you perform sanding operations.
5. Some material contains chemicals which may
be toxic. Take caution to prevent working
dust inhalation and skin contact. Follow
material supplier safety data.
6. Always use the correct dust mask/respirator
for the material and application you are work-
ing with.
7. Be sure that there are no cracks or breakage
on the pad before use. Cracks or breakage
may cause a personal injury.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing abrasive disc (Fig. 1)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the abrasive
disc.
To install the abrasive disc, first remove all dirt or for-
eign matter from the pad. Then attach the abrasive
disc to the pad, using the hook-and-loop system of
the abrasive disc and the pad. Be careful to align the
holes in the abrasive disc with those in the pad.
CAUTION:
Always use hook-and-loop system abrasive discs.
Never use pressure-sensitive abrasive discs.
Installing dust bag (Fig.2)
Install the dust bag on the tool so that the arrow with
“UP” indicated on the dust nozzle points upward.
Emptying dust bag
When the dust bag is about half full, switch off and
unplug the tool. Hold the tool as shown in Fig.3 and
remove the dust bag from the dust nozzle while
pressing the push button as shown in Fig. 4.
(Fig. 3 & 4)
After emptying the dust bag, insert the hook on the
dust nozzle into the rectangular hole on one side of
the dust bag frame and push up the dust bag frame
until it clicks into place on the push button. (Fig. 5)
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita bo5021k at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita bo5021k in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info