389392
6
Zoom out
Zoom in
Previous page
1/8
Next page
6
To remove the sandpaper:
1. Set the tool upside down so that the sandpaper is on
top.
2. Grasping one corner of the sandpaper, peel it from
the pad.
Note:
If the sandpaper is in good condition, save it for further
use.
When sanding in narrow, hard-to-reach areas (e.g., shut-
ters, blinds, louvres), attach the cone-shaped abrasive
papers to the end of the pad (bottom and top). To sand
the end of thin materials, fold the abrasive paper and
attach to the side of the pad as shown in Fig. 4 and 5.
Dust bag (Fig. 7)
The use of the dust bag makes sanding operations clean
and dust collection easy. To attach the dust bag, fit the
bag’s entry port onto the dust spout on the tool so that
the hole in the entry port is just over the protrusion on the
dust spout.
For the best results, empty the dust bag when it becomes
about half full, tapping it lightly to remove as much dust
as possible.
Installing paper dust bag
To install the paper dust bag, place the paper dust bag on
the paper dust bag holder with its front side upward.
Insert the front fixing cardboard of the paper dust bag
into the groove of the paper dust bag holder. (Fig. 8)
Then press the upper part of the front fixing cardboard in
arrow direction to hook it onto the claws. (Fig. 9)
Insert the notch of the paper dust bag into the guide of
the paper dust bag holder. Then install the paper dust
bag holder set on the tool. (Fig. 10 & 11)
Switch action (Fig. 12)
CAUTION:
Always check to see that the tool is switched off before
plugging in the tool.
To start the tool, press the “ON (I )” side of the switch. To
stop, press the “OFF ( O )” side of the switch.
Operation (Fig. 13 & 14)
Hold the tool firmly. Turn the tool on and wait until it
attains full speed. Then gently place the tool on the work-
piece surface. A finishing sander is generally used to
remove only a small amount of material at a time. Since
the quality of the surface is more important than the
amount of stock removed do not bear down on the tool.
Keep the base flush with the workpiece at all times.
Excessive pressure may damage the paper and shorten
tool life.
You can put a high polish on furniture or other fine sur-
faces by using a cloth under the tool.
For BO4561 and BO4563
This tool is handy for sanding louvres, etc. When sanding
louvres, insert the protruding portion of the pad between
the louvres and sand them using the upper or lower side
of the abrasive paper.
CAUTION:
Do not block motor vent with your finger or hand.
• Never run the tool without paper. You may seriously
damage the pad.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by a
Makita Authorized or Factory Service Centers, always
using Makita replacement parts.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita bo4553 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita bo4553 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita bo4553

Makita bo4553 User Manual - German, Danish, French, Italian, Portuguese, Spanish - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info