Manual Makita BO 6030 (page 5 of 15) (English, German, Dutch, Danish, French, Italian, Norwegian)

78697

Zoom out

Zoom in

1/15

Installing paper dust bag

To install the paper dust bag, place the paper dust bag on

the paper dust bag holder with its front side upward.

Insert the front fixing cardboard of the paper dust bag

into the groove of the paper dust bag holder. (Fig. 6)

Then press the upper part of the front fixing cardboard in

arrow direction to hook it onto the claws. (Fig. 7)

Insert the notch of the paper dust bag into the guide of

the paper dust bag holder. Then install the paper dust

bag holder set on the tool. (Fig. 8 & 9)

Front grip (Fig. 10)

Install the front grip on the tool so that its protrusions fit

into the matching notches in the front of the tool. Secure

the front grip using a screwdriver to tighten the screw

through the hole in the front grip.

Changing pad (Fig. 11)

Makita offers an extensive range of optional super soft

and standard equipped soft pads. Remove the screw

counterclockwise from the center of the base by a sharp

tap with a hammer on the hex wrench. After changing the

pad, tighten the screw clockwise securely.

Switch action (Fig. 12)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

Speed adjusting dial (Fig. 12)

The tool speed can be infinitely adjusted between

4,000 opm and 10,000 opm by turning the speed adjust-

ing dial, which is marked 1 to 5. Higher speed is obtained

when the dial is turned in the direction of number 5; lower

speed is obtained when it is turned in the direction of

number 1. Refer to the figure below for the relationship

between the number setting on the adjusting dial and the

kind of work.

A range: For polishing

B range: For finish sanding

C range: For regular sanding

NOTE:

The above figure shows standard applications. They may

differ under certain conditions.

Sanding operation (Fig. 13)

CAUTION:

• Never switch on the tool when it is in contact with the

workpiece surface, causing an injury to operator.

• Never run the tool without the abrasive disc. You may

seriously damage the pad.

• Never force the tool. Excessive pressure may decrease

the sanding efficiency, damage the abrasive disc or

shorten tool life.

Turn the tool on and wait until it attains full speed. Then

gently place the tool on the workpiece surface. Keep the

base flush with the workpiece and apply slight pressure

on the tool.

Polishing operation

CAUTION:

• Use only a Makita genuine sponge pad, felt pad or wool

pad (optional accessories).

• Always operate the tool at low speed to prevent work

surfaces from damage/burning.

• Never force the tool. Excessive pressure may decrease

the polishing efficiency and cause motor overload,

resulting in tool malfunction.

1. Applying wax (Fig. 14)

Use an optional sponge pad. Apply wax to the

sponge pad or work surface. Run the tool to smooth

out wax.

NOTE:

First, wax a non critical portion of the work surface to

make sure that the tool will not scratch the surface or

result in uneven waxing.

2. Removing wax (Fig. 15)

Use an optional felt pad. Run the tool to remove

wax.

3. Polishing (Fig. 16)

Use an optional wool pad. Run the tool and apply

the wool pad gently to the work surface.

Orbits per minute

A range

B range

C range

Dial setting

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BO 6030 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BO 6030 Manual

Product: