Manual Makita 9920 (page 5 of 8) (English, German, Dutch, Danish, French, Italian, Norwegian)

78502

Zoom out

Zoom in

1/8

ENGLISH

Explanation of general view

1 Lever

2 Base

3 Adjusting knob

4 Dust spout

5 Dust bag

6 Fastener

7 Lock button

8 Switch trigger

9 Speed adjusting dial

0 Optional hose 28 mm in inner

diameter

q Hose of vacuum cleaner

w Vacuum cleaner

e Belt sander stand

r Guide fence

t Sanding shoe

y Limit mark

u Brush holder cap

i Screwdriver

SPECIFICATIONS

Model Belt size Belt speed Overall length Net weight

9902 ............. 76 mm x 533 mm 440 m/min. 296 mm 4.3 kg

9903 ............. 76 mm x 533 mm 210 – 440 m/min. 296 mm 4.3 kg

9920 ............. 76 mm x 610 mm 210 – 440 m/min. 334 mm 4.5 kg

9404 ............. 100 mm x 610 mm 210 – 440 m/min. 334 mm 4.7 kg

•

Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and can only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

safety instructions.

ADDITIONAL SAFETY RULES

1. Hold machines by insulated gripping surfaces

when performing an operation where the cut-

ting machine may contact hidden wiring or its

own cord. Contact with a ‘‘live’’ wire will make

exposed metal parts of the machine ‘‘live’’ and

shock the operator.

2. Hold the machine firmly with both hands.

3. Make sure the belt is not contacting the work-

piece before the switch is turned on.

4. Keep hands away from rotating parts.

5. Do not leave the machine running. Operate the

machine only when hand-held.

6. This machine has not been waterproofed, so

do not use water on the workpiece surface.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing abrasive belt (Fig. 1)

Important:

Always be sure that the machine is switched off and

unplugged before installing or removing the belt.

Pull the lever all the way out and install the belt over

the rollers, then return the lever to the original posi-

tion.

CAUTION:

When installing the belt, make sure that the direction

of the arrow on the back of the belt corresponds to the

one on the machine itself. (Fig. 2)

Adjusting belt tracking (Fig. 3)

Switch on the machine and make sure that the belt is

aligned properly. If the edge of the belt extends

beyond the edge of the base or the edge of the belt

retracts more than 6 mm away from the edge of the

base, use the adjusting knob to adjust the belt track-

ing.

Dust bag (Fig.4&5)

Attach the dust bag onto the dust spout. The dust

spout is tapered. When attaching the dust bag, push

it onto the dust spout firmly as far as it will go to

prevent it from coming off during operation. For the

best results, empty the dust bag when it becomes

about half full, tapping it lightly to remove as much

dust as possible.

Switch action (Fig. 6)

CAUTION:

•

Before plugging in the machine, always check to

see that the switch trigger actuates properly and

returns to the ‘‘OFF’’ position when released.

•

The machine should not be in contact with the

workpiece surface when you turn the machine on or

off. Otherwise a poor sanding finish or damage of

the belt may result.

To start the machine, simply pull the trigger. Release

the trigger to stop. For continuous operation, pull the

trigger and then push in the lock button. To stop the

machine from the locked position, pull the trigger fully,

then release it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 9920 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 9920 Manual

Product: