Manual Makita 9036 (page 3 of 13) (English, German, Dutch, Danish, French, Italian, Norwegian)

389726

Zoom out

Zoom in

1/13

ENGLISH

Explanation of general view

1 Clamper

2 Abrasive paper

3 Lock button

4 Switch trigger

5 Punch plate

SPECIFICATIONS

Model 9036

Pad size................................................ 93 mm x 185 mm

Orbits per min........................................................12,000

Overall length ......................................................238 mm

Net weight............................................................... 1.4 kg

• Due to our continuing programme of research and

development, the specifications herein are subject to

change without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed Safety

instructions.

SPECIFIC SAFETY RULES

GEB021-1

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to sander safety rules. If you use this tool unsafely or

incorrectly, you can suffer serious personal injury.

1. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a "live" wire will make exposed metal

parts of the tool "live" and shock the operator.

2. Always use safety glasses or goggles. Ordinary

eye or sun glasses are NOT safety glasses.

3. Hold the tool firmly.

4. Do not leave the tool running. Operate the tool

only when hand-held.

5. This tool has not been waterproofed, so do not

use water on the workpiece surface.

6. Ventilate your work area adequately when you

perform sanding operations.

7. Some material contains chemicals which may be

toxic. Take caution to prevent working dust inha-

lation and skin contact. Follow material supplier

safety data.

8. Use of this tool to sand some products, paints

and wood could expose user to dust containing

hazardous substances. Use appropriate respira-

tory protection.

9. Be sure that there are no cracks or breakage on

the pad before use. Cracks or breakage may

cause a personal injury.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

OPERATING INSTRUCTIONS

Installing or removing abrasive paper (Fig. 1)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the paper.

Press the clamper. Insert the paper end into the clamper,

aligning the paper edges even and parallel with the sides

of the base. Then release the clamper.

Repeat the same process for the other end of the base,

maintaining the proper paper tension.

CAUTION:

After inserting the paper, make sure the teeth of the

clamper hold it securely. Otherwise the paper will be

loose and subject to slippage, resulting in uneven sand-

ing operation.

Switch action (Fig. 2)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

Operation (Fig. 3)

Hold the tool firmly. Turn the tool on and wait until it

attains full speed. Then gently place the tool on the work-

piece surface. A finishing sander is generally used to

remove only a small amount of material at a time. Since

the quality of the surface is more important than the

amount of stock removed, do not bear down on the tool.

Keep the base flush with the workpiece at all times.

Excessive pressure may damage the paper and shorten

tool life.

You can put a high polish on furniture or other fine sur-

faces by using a cloth under the tool.

CAUTION:

• Do not block motor vent with your finger or hand.

• Never run the tool without paper. You may seriously

damage the pad.

When you wish to perform clean sanding operation, pro-

ceed as follows:

Place the punch plate (optional accessory) over the

paper so that the guide of the punch plate is flush with

the sides of the base. Then press the punch plate to

make holes in the paper. (Fig. 4)

Remove the cap from the dust spout on your tool and

connect a vacuum cleaner to your tool using a hose

(optional accessory). Be sure to read cleaner’s instruc-

tion manual. (Fig. 5)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 9036 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 9036 Manual

Product: