Manual Makita 6820V (page 3 of 12) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

448229

Zoom out

Zoom in

1/12

ENGLISH

Explanation of general view

1 Locator

2 Stopper

3 Magnetic bit holder

4Bit

5 Locking sleeve

6 Speed control screw

7 Switch trigger

8 Lock button

9 Reversing switch lever

SPECIFICATIONS

Model 6820V

Capacities

Self drilling screw .................................................6 mm

Drywall screw ...................................................... 5 mm

Driving shank .................................................. 1/4” Hex

No load speed (min

–1

) ......................................0 – 4,000

Overall length .....................................................268 mm

Net weight .............................................................. 1.3 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed Safety

instructions.

SPECIFIC SAFETY RULES

GEB017-1

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict

adherence to screwdriver safety rules. If you use

this tool unsafely or incorrectly, you can suffer

serious personal injury.

1. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

3. Hold the tool firmly.

4. Keep hands away from rotating parts.

5. Do not touch the bit or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious per-

sonal injury.

OPERATING INSTRUCTIONS

Removing or installing the bit (Fig. 1)

Important:

Always be sure that the tool is switched off and

unplugged before removing or installing the bit.

To remove the bit, first pull the stopper out of the locator.

Then grasp the bit with a pair of pliers and pull the bit out

of the magnetic bit holder. Sometimes, it helps to wiggle

the bit with the pliers as you pull. To install the bit, push

the bit firmly into the magnetic bit holder. Then install the

stopper by pushing it firmly into the locator.

Depth adjustment (Fig. 2, 3 & 4)

Push the locking sleeve in toward the motor and turn

slightly clockwise to lock it.

Turn the locator to adjust the depth. Initially, adjust the

locator so that the tip of the locator is flush with the base

of the screw head. One full turn of the locator equals 1.5

mm change in depth. After adjusting the locator, unlock

the locking sleeve. Turn the locking sleeve slightly so that

the protrusions on the locking sleeve engage in the

notches in the locator. Drive a trial screw into your mate-

rial or a piece of duplicate material. If the depth is not

suitable for the screw, continue adjusting until the proper

depth setting is obtained.

NOTE:

Before starting your job, always test-drive a sample

screw into a piece of the installation workpiece so that

you are sure to have the right depth and desired adjust-

ment.

Switch action (Fig. 5)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To start the tool, simply pull the trigger.tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop. For continuous operation, pull the trig-

ger and then push in the lock button. To stop the tool from

the locked position, pull the trigger fully, then release it. A

speed control screw is provided so that maximum tool

speed can be limited (variable). Turn the speed control

screw clockwise for higher speed, and counterclockwise

for lower speed.

NOTE:

Even with the switch on and motor running, the bit will not

rotate until you fit the point of the bit in the screw head

and apply forward pressure to engage the clutch.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 6820V in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 6820V Manual

Product: